Electronics Forum: dek dek printing sensor (107458) o (Page 1 of 2)

DEK288 Machine's

Electronics Forum | Thu Aug 22 04:08:17 EDT 2002 | Jason Baldwin

Symptom: Board Stuck on Print Conveyor error messages. Cause: Board not flagging the camera sensor. Remedy: Check the following items: � Check the camera sensor can see the board underneath. � Check the camera sensor calibration (in Tools, Camera Re

DEK 265GSX HOOD OPEN ERROR

Electronics Forum | Mon Sep 20 14:15:32 EDT 2010 | dekhead

"System Suspended While Cover is Opened" indicates front or rear cover opened; not the head being raised. Therefore there is an issue with one of the cover interlocks not being made properly. Note there are 2 switches on each (NO and NC) one goes int

Re: Proflow of DEK screen printer

Electronics Forum | Wed Sep 08 08:25:26 EDT 1999 | Brad Kendall

Listed below are the issues Viking has been experiencing since the | installation of the Proflow Head: | 1. After installing new 350mm Wiper foil with metal | strip glued on it, It worked for about a week and suddenly meta

DEK print limit

Electronics Forum | Tue Jun 25 21:13:10 EDT 2024 | jeremyc

I also happen to be running into this issue. A PCB we're trying to program has a width larger than the max board width. On our O2i, it says 12.992in is the max board width. HOWEVER the tech specs of Dek Horizon O2i advertise a max print area of 508m

Re: Proflow of DEK screen printer

Electronics Forum | Tue Sep 07 15:28:13 EDT 1999 | Earl Moon

Listed below are the issues Viking has been experiencing since the installation of the Proflow Head: 1. After installing new 350mm Wiper foil with metal strip glued on it, It worked for about a week and suddenly metal stri

DEK 248 squeegee error

Electronics Forum | Fri Feb 15 21:52:06 EST 2013 | nikyta

Most likely it is a faulty cable in the e-chain . You can test it in diagnostic: lower the back squeege and manually move back and forth for its entire travel the print carriage while monitoring the sensor output of the squeege. You will see at some

DEK 265GSX

Electronics Forum | Fri Apr 29 22:35:01 EDT 2016 | dekhead

Pneumatic failure is a good guess, as GSX/LT are renowned for their leaky airlines. However on this I would doubt, since the Board stop is a single throw pneumatic with a spring to retract. The return spring broken / disconnected is certainly a possi

up2000 HiE hates me

Electronics Forum | Tue Oct 31 13:15:13 EST 2006 | realchunks

SWAG is prolly right. You can verify the tactile sensor by watching the machine carefully. When finding the stencil height, make sure the board goes all the way up and touches the stencil to trigger the tactile. If it doesn't, then something is wr

Screening Solder Print paste m/c

Electronics Forum | Tue Jul 18 23:11:03 EDT 2006 | Utog Oten

Hello folks I am seeking advice and guidance on a screen print machine who the best manufacturers are of this equipment and so fourth. I got budgetary approval from the management to purchase a medium volume electronics line. Our engineer sup. seems

solder paste

Electronics Forum | Wed Jul 27 09:58:05 EDT 2011 | davef

Pressure printing systems Conventional stencil printing techniques have fundamental limitations as regards paste handling: The volume of paste available for printing is limited, so frequent replenishment is necessary Paste is difficult to c

  1 2 Next

dek dek printing sensor (107458) o searches for Companies, Equipment, Machines, Suppliers & Information

ISVI - Industrial Sensor Vision International Corporation
ISVI - Industrial Sensor Vision International Corporation

Industrial Sensor Vision International specializes in advanced camera technology of high resolution fast speed cameras for automation, AOI, 2-D/3-D, SPI inspection and wafer inspection.

Manufacturer

3 Morse Road 2A
Oxford, CT USA

Phone: +1 203 592 8723

Blackfox IPC Training & Certification

High Precision Fluid Dispensers
pressure curing ovens

Best Reflow Oven
SMT feeders

World's Best Reflow Oven Customizable for Unique Applications


Original SMT Feeders and spares for Panasonic, Fuji , Yamaha, Juki , Samsung