Electronics Forum: delta 3 wave fluxer (Page 1 of 13)

vitronics delta 6622 fluxer

Electronics Forum | Thu Mar 18 07:58:43 EDT 2010 | mun4o

It is a pressurized system, and , Yes , there are a message "No flow nozzle 1".Our machine have not 'ShoRate' gauge at the back of the machine.There are only 3 gauge for flow on the front side , like watch ???

vitronics delta 6622 fluxer

Electronics Forum | Wed Mar 17 04:26:44 EDT 2010 | mun4o

Hi, we have vitronics delta 6622 in your production.Problem with fluxer starting 3 weeks ago.Fluxer moving, but not spraing????I check flux system , and dont find any problems with machine.Clean the spray nozzle with compressed air , but nothing.may

soltec delta wave

Electronics Forum | Thu Oct 22 12:30:33 EDT 2020 | emeto

So is the initial motor at fault failing now or the one from zone 3?

soltec delta wave

Electronics Forum | Wed Oct 21 13:50:50 EDT 2020 | kierantennant

hi, I am experiencing a problem with our wave solder machine where zone 2 (forced convection) fan will not work when called upon. so we swapped it with zone 3 to make sure the motor was not at fault and it wasn't so we moved the A1 into a different 2

vitronics delta wave malfunction errors :pcb expected at exit

Electronics Forum | Fri Sep 14 03:43:16 EDT 2012 | mili

Hello!I have a delta wave with these problems:offtime of lambda wave tracking is too long and when modify offtime setting to a negative value for a fast stop on tracking position of lambda wave, the wave pass on stand-by with a delay of half of leg

vitronics delta wave malfunction errors :pcb expected at exit

Electronics Forum | Fri Sep 14 10:53:25 EDT 2012 | mili

In Setup menu there is a last option Debug. Debug choosing a window with Rack0, Rack1, Rack2, Rack3, log RS485 opens. Choosing rack0 a window with parameters S3 boxes 1 to 12 Input and certain boxes are checked, S4 Output from 1-8, from 1-8 S5 Outpu

vitronics delta wave malfunction errors :pcb expected at exit

Electronics Forum | Fri Sep 14 08:53:43 EDT 2012 | mbnetto

Hi, Recently we acquired a Delta 3 and I noticed everytime we change any value regarding to the tracking system, as chip or main wave - offtime/ontime- with boards loaded on it, the tracking system doesnt work well. sometimes it turns off the wave o

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Mon Nov 09 09:44:22 EST 2015 | davef

Purpose. This describes setting-up a wave soldering system set-up for a new assembly design or checking a wave solder machine operation with a test board. Applicability. To be used for new design printed circuit assembles and during machine accept

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Sun Nov 08 15:27:25 EST 2015 | davef

Thinner: Flux thinner, NOT paint thinner We kept a spare stone in thinner in inventory. We cut PVC pipe to size, cap in one end, screw thread on the other, stone inside, filled with flux thinner and covered with a screw cap. I don't remember who we

Blowholes during wave soldering

Electronics Forum | Thu Sep 06 17:37:05 EDT 2007 | hakerem

Hi Joris - There is an excellent wave solder guide called "Take No Prisoners" that includes instructions for attacking and eliminating solder balls and preventing their recurrence: 1. Increase Dwell Time Solder balls are normally caused by too much f

  1 2 3 4 5 6 7 8 9 10 Next

delta 3 wave fluxer searches for Companies, Equipment, Machines, Suppliers & Information