Electronics Forum: delta 5 solder wave (Page 2 of 60)

Delta wave solder

Electronics Forum | Tue Oct 11 14:02:59 EDT 2016 | mnorthey

We have a slider Bar on the back side of our Delta Wave. It is adjustable and slides up and down (adjusting bolt) on the back edge of the Lamda Wave to prevent this problem; keeping the trough behind the Lamda is essential as well. Along with attenti

Delta wave solder

Electronics Forum | Mon Jun 12 07:52:21 EDT 2017 | tch

We have had this issue on our Delta 3 waves and determined that there are small pin holes in the solder pot. We had plates welded to the outside of our solder pot on the lead free wave and this bought us enough time until we could replace the wave, a

Delta wave solder

Electronics Forum | Mon Jun 05 03:06:24 EDT 2017 | mun4o

hi, are you resolve the problem? I have the same solder wave and the same problem. Can you advise my something? Regards

Spartan wave solder machines

Electronics Forum | Thu Nov 20 18:57:52 EST 2014 | warwolf

I can only say it looks okay for what you need, you will want a dual wave system it can make things so much easier. One thing to check would be the wave nozzle sizes I can see that the conveyor will do up to 15" but thats not to say the nozzle is

Delta wave solder

Electronics Forum | Wed Oct 12 08:34:48 EDT 2016 | assuredtech

Speaking from experience, the solder pot surface has become "wetted" so to speak, so solder will naturally wick and seek. Allow the level to go low (perhaps 1 inch plus), clean the top surface area of the solder pot as best as you can - try to remove

Delta wave solder

Electronics Forum | Sat Oct 08 04:24:37 EDT 2016 | aaronpainter

We are having an issue with the solder bars hanging the solder feeder dripping down the back side of the pot, and leaking in to the area where the terminal block for the elements on the pot are. We have tried aluminum tape to close off the gap betwee

Spartan wave solder machines

Electronics Forum | Thu Nov 20 14:49:54 EST 2014 | joe98375

Greetings, I am looking into buying a wave solder machine for medium production of 100% through hole boards (~8.5"X12" dimension, not many layers, no high density part areas,

wave solder machine

Electronics Forum | Tue May 17 10:11:54 EDT 2005 | russ

I would use a foam fluxer since spraying rosin will make the stickiest nastiest mess you can imagine. 18 layer board huh? You will want convection preheat, both top and bottom preheaters, preheat tunnel of at least 4-5', a chip wave, laminar flow w

Re: wave solder process

Electronics Forum | Mon Jun 21 14:55:27 EDT 1999 | JohnW

| | Does anyone know where I can find a list of things to do to when troubleshooting issues during the wave solder process? | | | | for example: | | | | Solder Bridge | | 1.verify amount of flux been aplied. | | 2.verify turbulance on your solder w

Re: wave solder process

Electronics Forum | Thu Jun 17 20:35:51 EDT 1999 | Earl Moon

| | | Does anyone know where I can find a list of things to do to when troubleshooting issues during the wave solder process? | | | | | | for example: | | | | | | Solder Bridge | | | 1.verify amount of flux been aplied. | | | 2.verify turbulance on


delta 5 solder wave searches for Companies, Equipment, Machines, Suppliers & Information

Solder Paste Dispensing

High Resolution Fast Speed Industrial Cameras.
Sell Used SMT & Test Equipment

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Voidless Reflow Soldering

High Throughput Reflow Oven
PCB Handling with CE

World's Best Reflow Oven Customizable for Unique Applications


"回流焊炉"