Electronics Forum: door (Page 1 of 27)

SMT Line and vibration next door

Electronics Forum | Mon Jan 13 11:29:39 EST 2020 | rlising

We are planning on installing an SMT Line in our building. We own 75% of the building, there is a crossfit gym next door and they tend to drop weights where we can feel the vibration. Should we be concerned with the SMT Line being set up on that end

SMT Line and vibration next door

Electronics Forum | Mon Jan 13 14:44:19 EST 2020 | dwl

I wouldn't think the vibration from weights dropping would be significant enough to effect the SMT machines. If you are concerned, look into placing vibration dampening pads under the machine feet. you don't need anything fancy, just neoprene pads wo

Panasert MPA 80 NM 2523

Electronics Forum | Wed Mar 13 17:17:42 EDT 2013 | isd_jwendell

I don't know your machine, but on mine the interlock is the large access door. It's done so that you cannot open the cover while running, but it also checks for a closed door at startup due to head homing sequence. Yours may be similar in that it won

CP6-4000 FUJI TECH in CALIFORNIA???

Electronics Forum | Fri Jul 17 19:43:20 EDT 2009 | fujiphil

Have you eliminated the hardware N.G.? Check the connection for the rear door. If the connection are ok, try to bypass the key. short the two wires for the rear door. If the rear door problem is corrected, check the rear door switch physically. Reg

QUAD 4C motor error #5

Electronics Forum | Thu Aug 29 14:20:17 EDT 2013 | nophsem

Thanks for the response bobpan! LED's on the driver cards work well (green with doors closed and both red&green on with door open), and I don't use the carts. The head doesn't move after power on and inmediately you can listen alarm.

Meridian 1020P servo wont start

Electronics Forum | Thu Jun 26 05:07:19 EDT 2014 | bobpan

On the older machines if the z-axis has springs on them sometimes they get weak and when you open the door the z will not stay up. Before closing the door manually push the z up if they are dropping down then enable the motor power. If this is the ca

QSP2-PLUS

Electronics Forum | Wed Sep 02 14:58:35 EDT 2015 | derrikf

Steve, Does said phenomena occur at a particular time? Or is it seemingly random? What sensors are you referring to? The door sensors, (as in you have the doors open and the gantries move)?

Cure Ovens and Cycle Interuption

Electronics Forum | Fri Dec 17 13:23:15 EST 1999 | Chris

I have an underfill material which takes 6 hours to cure. It works great, better than any other underfill I have ever used. A vertical cure oven is too expensive. I am currently using batch style ovens and opening the oven door as additional produ

Cpk Variables Control for Paste Printing

Electronics Forum | Fri Apr 05 01:59:17 EST 2002 | darby

You got me dander up now. Anything gettin' out the door there?

Panasert MPA 80 NM 2523

Electronics Forum | Wed Mar 13 19:48:31 EDT 2013 | marcelorotofrance

The front door has as security switch, indeed. It works ok. A lever switch for override the door switch is also included from factory. (It don´t look good from the safety point of view but, you know). There is also a presostatic switch on the air reg

  1 2 3 4 5 6 7 8 9 10 Next

door searches for Companies, Equipment, Machines, Suppliers & Information

Circuit Board, PCB Assembly & electronics manufacturing service provider

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Fluid Dispensing, Staking, TIM, Solder Paste

Training online, at your facility, or at one of our worldwide training centers"
IPC Training & Certification - Blackfox

Component Placement 101 Training Course
best pcb reflow oven

Reflow Soldering 101 Training Course
SMT feeders

Software for SMT placement & AOI - Free Download.
Hot selling SMT spare parts and professional SMT machine solutions

Private label coffee for your company - your logo & message on each bag!