Electronics Forum: ekra problem (Page 1 of 7)

ekra e5 blades not dropping.

Electronics Forum | Mon Sep 29 15:28:29 EDT 2014 | dustin

After getting the last issue I had fixed through here. I thought I would try to see if there is a solution for another issue. I have and ekra e5 screen printer and it has a problem with the blades not dropping when they should. If I set up single dir

ekra e5 blades not dropping.

Electronics Forum | Tue Sep 30 14:06:16 EDT 2014 | nicodj77

Hi Dustin, It happened to us once and it was something very simple. We did maintenance to the Squeegee head and the problem was that the Squeegee head cover was not put back in place correctly, so it was interfering with the Squeegee up/down movement

ekra e5 blades not dropping.

Electronics Forum | Thu Oct 02 04:39:08 EDT 2014 | oxygensmd

I had the same problem with my E5. At first check the cover and valves in the squeegees head. For me wasn't help, I didn't found any fault, jamm. In my machine there is two adjustable valve over the transport at output-vent. I tried to readjust the

Ekra E4 stencil wipe problem

Electronics Forum | Thu Sep 08 15:17:08 EDT 2016 | bobpan

black on top / blue on bottom both sides good luck

Ekra E4 stencil wipe problem

Electronics Forum | Thu Sep 15 11:50:30 EDT 2016 | bobpan

hope this helps

Ekra E5 cleaner dispenser problem

Electronics Forum | Fri Jan 03 00:22:02 EST 2003 | Steve

We have an Ekra E5 that uses what looks like standard auto valve stems to dispense the cleaning fluid. They leak.. Are they just standard schrader valves or are special to withstand the chemistry of stencil cleaner?

Ekra E5 cleaner dispenser problem

Electronics Forum | Sat Jan 04 09:48:22 EST 2003 | Steve

Yes this is 1st generation, a large metal tube positioned horiz. with valves to wet the wiping towel all at once. We have the newer sys. on the other Ekra, motor driven gear rack and selonoid dispenser.I talked w/ their tech. and got "Oh yea,,they al

Ekra E4 stencil wipe problem

Electronics Forum | Thu Sep 08 13:14:11 EDT 2016 | claudea2

Hello, we have an Ekra E4 that we bought used and the stencil wipe never worked. We found that the air tubing for the up (black)& down (blue) of the wipe roll is missing. There are 2 push connectors for up and 2 for down to receive the tubes. Does an

Ekra E5 cleaner dispenser problem

Electronics Forum | Mon Jan 06 11:04:39 EST 2003 | slthomas

Bummer. Are you using the EPAC stuff that they recommend, or something else? We used IPA for a while, then changed to a run-of-the-mill stencil cleaning solvent (aliphatic hydrocarbon based, like the EPAC solvent) that's a lot cheaper and does the

Ekra E5 cleaner dispenser problem

Electronics Forum | Fri Jan 03 10:55:57 EST 2003 | slthomas

I'm not sure what you mean by "standard auto valve stem". Ours use EFD pumps to dispense fluid. I think there used to be a sort of a drip system that attempted to wet the entire length of the paper all at once but have never seen one. Which system

  1 2 3 4 5 6 7 Next

ekra problem searches for Companies, Equipment, Machines, Suppliers & Information

Void Free Reflow Soldering

World's Best Reflow Oven Customizable for Unique Applications
Selective Soldering Nozzles

We offer SMT Nozzles, feeders and spare parts globally. Find out more
Circuit Board, PCB Assembly & electronics manufacturing service provider

High Precision Fluid Dispensers
PCB Handling with CE

High Throughput Reflow Oven
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
PCB Depanelizers

"回流焊炉"