18 electrovert omniflex 7 reflow oven jmw results

Electronics Forum: electrovert omniflex 7 reflow oven jmw (Page 1 of 2)

schematics/manual electrovert omni 7 (1998)

Electronics Forum | Wed Dec 08 17:48:18 EST 2010 | katguts69

looking for schematics for electrovert omni 7 reflow oven. manufactured in 1998. help!

5 zone reflow oven

Electronics Forum | Wed Feb 23 18:27:12 EST 2005 | gpaelmo

Hi Indy, Check http://www.jmw-inc.com (they are in the midwest so shipping will not be too bad going out east). I bought 2 MPM printers and a pick and place machine from them late in 2004. I know they have 5-zone reflow and 7-zone ovens there (elect

Electrovert Omniflo 7 reflow ovens

Electronics Forum | Thu Aug 30 13:22:47 EDT 2001 | arzu

180deg More important are the preheat and soakzones and temp ramps. How to check: I used to do it as follows: use a TEST-PCB with fixed thermocouples and connect it to the mole. Print the profile on transparant paper. do it again e.g. each week and

Electrovert Omniflo 7 reflow ovens

Electronics Forum | Thu Aug 30 11:59:00 EDT 2001 | Spanky

Hey all, I have 3 questions about reflow. Hopefully someone can help me. 1. I am having a problem. I set the peak at 230 and my mole thermocouples are telling me the temp in that zone gets to 237. How is this possible even if the thermocouple

Electrovert Omniexcell 7 Center Support

Electronics Forum | Mon Jun 24 13:01:24 EDT 2013 | quaker332007

Can anyone help me with the center support on this oven? The support is rising up to high and causing the board to rock during reflow. Is the away to lower the center support?

Reflow oven

Electronics Forum | Fri Jun 26 10:33:08 EDT 2015 | Asif

Hello Professionals, Good morning, We are circuit card manufacturer for the Aerospace industry with low volume and High mix level. We have a plan to Purchase a NEW REFLOW OVEN. Currently we are using Electrovert BRAVO reflow oven which is about 8 yea

Soldering oven

Electronics Forum | Mon Jan 19 08:37:16 EST 2009 | lkpdsund

Hello all! We possess a speedline electrovert omniflo 7 reflow oven at my site. Last week we examined how the solder profile was affected by fan-speed and by providing the soldering process with compressed air(O2) or nitrogen(N2). We also ran the sa

BTU Paragon 150 Reflow Oven

Electronics Forum | Mon Apr 24 14:04:44 EDT 2006 | pjc

You did not tell us where your boards fit on the thermal mass range. That is key. I've run Pb Free low to medium thermal mass boards with good results on a 5 zone oven (5 top/5 bottom). You should not have a problem running a medium thermal mass boa

Full IR Reflow versus conventional convection ?

Electronics Forum | Mon Jan 23 09:00:22 EST 2006 | Chunks

Wow, these are still around? Don't go IR, especially with these units. They are very inconsistent. Maybe for adhesive, but I wouldn�t try reflow with them. Yes, you can reflow with them, but this model of oven will constantly change on you. I

Omniflo 7e schematics + Manuals

Electronics Forum | Wed Jan 19 14:43:51 EST 2011 | davidalvarez

Im looking for manuals + schematics and repair information for an electrovert omniflo 7e reflow oven manufactured in 1999, also intrested in the Bill Of Materials if available. Any information on where these can be obtained and where replacement part