13 fa inspection results

Electronics Forum: fa inspection (Page 1 of 2)

First piece inspection

Electronics Forum | Fri Jan 11 02:07:08 EST 2002 | ianchan

For repeated model runs, we go ahead with the SMT run, whilst the QA does the FA inspection. Limit FA timing to 2h or less...(simple boards yield faster time cycles). For new model runs, yep, we wait for QA to confirm the FA inspection, only with QA

Laser Machine for Solder Paste Volume

Electronics Forum | Wed Dec 08 18:22:47 EST 2004 | msjohnston1

Here is a list of companies that have solder paste inspection equipment that use a laser for measurements www.gsilumonics.com www.orbotech.com/products_assembly_main.asp www.fa.panasonic.co.jp/products/smt/inspection/main/ipm_e.html

First piece PCBA validation

Electronics Forum | Tue May 31 16:52:57 EDT 2011 | xray

Hi SSager, Check out the FA Inspector. It provides 1 Automatic Detection Mode and 2 Manual Inspection Modes. Its used to automate First Article Inspection Tasks and enhance today's principally manual process using microscopes and pen and paper. T

Desktop AOI machine

Electronics Forum | Tue Aug 27 18:14:12 EDT 2019 | spoiltforchoice

You don't want an AOI machine you want an FAI (First Article Inspection) like one of these http://www.aoisystems.com/Scanner-Based-FA-Inspector.html (note some of the products here call themselves AOI, arguably they are not.) Or https://www.quins.de/

First Article Inspection, Lower End AOI

Electronics Forum | Tue May 31 16:31:02 EDT 2011 | xray

Hi, Besides the 2 machines mentioned which are part comparison machines that require the operator to provide a pass/fail on each ref id, there is a system called the FA Inspector which offers the mode described above and two additional modes: 1. Au

YESTECH OR MVP? LOOKING FOR AOI.

Electronics Forum | Fri Sep 05 19:56:56 EDT 2008 | hegemon

We did extensive side by side (by side) testing of three AOI machines Omron, YesTech and Mirtec. In the end, even with weighted scores, the difference in the top two machine was still only four/tenths of a point. Third place was a distant 14 points

Used X-ray is hunted! VJ-1000 is good candiate

Electronics Forum | Tue Jul 30 20:32:39 EDT 2002 | YH Shiau

We look for a real-time X-ray machine with 90~100KV power to do the BGA/ FCCSP assmebly inspection. The key role for this x-ray will be defined as process control tool and PCBA level FA. VJ-1000 from VJ Electrnix is kind suitable for our needs. D

pbga substrate crack vision system

Electronics Forum | Thu Sep 24 18:57:03 EDT 2009 | davef

From "siliconfareast.com": Basic Die Cracking FA Flow 1) Failure Information/Device and Lot History Review. Understand the customer's description of the failure, i.e., the failure mode, where it was encountered, what conditions the sample was subject

BGA failure after coating

Electronics Forum | Thu Oct 01 07:03:55 EDT 2009 | davef

We doubt that Humiseal 1A33 is causing opens in your assemblies. We'd guess the opens occur earlier in the process, but are not hard failures. So, you pass your tests. When applied, the conformal coat flows into the gap in the ball crack and insulate

advice on used PnP

Electronics Forum | Mon Jun 29 15:10:10 EDT 2020 | spoiltforchoice

I would specifically look at the FLX2011 models with a V for vision (they otherwise come with Cyberoptics laser alignment as standard, although that would also work if you are not inspecting BGA balls). They come with software that I think is called