Electronics Forum | Mon Aug 21 10:47:48 EDT 2006 | FredC
Hello Mika, I just checked a windmill and a test nozzle we have on the bench. The useful travel of the nozzle before the risk of the crosspin getting stuck in the loading gate is 1.5mm, if it gets stuck it is the nozzle is 1.7 up. If the cross pin is
Electronics Forum | Tue Nov 06 07:37:02 EST 2007 | cyber_wolf
Does anyone out there have a method of cleaning CP6 shaft clutches that is "easier" ? I am not a fan of just pulling the shaft down and wiping it out. I like to take them apart and clean/lube them. It is a pain to get the crowns back on without rip
Electronics Forum | Tue Mar 11 16:24:12 EDT 2014 | sumote
Does anyone have a copy of the feeder repair/maintenance for the CP6 and IP3 feeders? I need the ones that have exploded views with part numbers. I have had them in a previous life so I know they exist. If someone has a pdf file they could sen
Electronics Forum | Tue May 26 00:22:35 EDT 2015 | hemantp
help required for understanding correct nozzle for the fuji feeder ( CP642 or QP242 )mounting of the SMT Pogo pins ( single Pin ) The Part nos are 1. P/N : HCS0712SM01-B20150507 (Female pin) and 2. P/N : N005M1-01C000CR (Male pin).
Electronics Forum | Sun Mar 21 22:03:35 EST 1999 | Nick
It looks like your holders now require some maintenance. You will need to throughly clean all the holders of all dirt debris and then relube the holder lightly with T&D or grease. You will only need to lube the shaft of the nozzle change enagager an
Electronics Forum | Tue Sep 10 23:37:22 EDT 2002 | Steve E
Dear Sir I can assure you that I have personal experience with the part in question.This part will run with the recommend vision types ( 11 & 12 ). I noticed You neglected to state how old the machine was, and the amount of hours. The CP-6 series hav
Electronics Forum | Fri Mar 12 23:05:37 EST 1999 | Joe Cameron
Has anyone got problems with their Fuji CP6* holders sticking and not indexing the nozzles? We find about 2 or 3 holders seizing up on us every two weeks or so. It's really frustrating, not to mention the damage it can cause on the machine and the
Electronics Forum | Mon Aug 21 10:36:25 EDT 2006 | vikkaraja
I Think I understand your problem. But I think it would be best if you just go in the program and change/check your componet height as needed. It does not take much time. Check your cap height, modify shape data as needed, generate your program and
Electronics Forum | Fri Mar 24 22:03:23 EST 2006 | mika
Hi all, Is there anybody out there who have some experience of Valor Trilogy 5000 in respect of programming/line balancing SMT-lines consisting of Fuji CP6-4's and UIC-GSM's? Our company is seriously thinking about to go for UniCam and their solution
Electronics Forum | Sat Sep 25 09:18:40 EDT 1999 | Steve E ( Fuji America )
| Question for you SMT guru's out there. | | What is the best way to support boards on Fuji's CP6 machine's x-y table...particularly for 2nd side SMT where the support side already has parts... I am toying around with the following methods: | | 1.
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694
