Electronics Forum | Mon Jan 18 20:25:49 EST 1999 | Dave F
| I know there was some discussion a few months ago on this topic but I don't think a good solution was offered for checking CpK using chips using a chip shooter. I am looking for a way to measure this on our Fuji CP6-4000. Any suggestions? | | Je
Electronics Forum | Mon Mar 20 22:33:08 EST 2000 | RJJOHNSON
Cim system is what we used on cp6 d axis tables.It worked very well.I liked it and it was for pre run and during run feeder feeding.Uses a barcode reader and reads bottom of d axis where barcode are to match what is assigned to a slot by pre scanning
Electronics Forum | Mon Mar 20 22:33:08 EST 2000 | RJJOHNSON
Cim system is what we used on cp6 d axis tables.It worked very well.I liked it and it was for pre run and during run feeder feeding.Uses a barcode reader and reads bottom of d axis where barcode are to match what is assigned to a slot by pre scanning
Electronics Forum | Fri Aug 13 14:52:15 EDT 2004 | cabjerk
Hi All: I posted this thread a while back and got no response. So, I'm trying it again. We have found a machine called the GAM-20F to calibrate our Fuji CP6 feeders. Has anyone ever used one of these? The price is in the 5-6K range and is from SMT
Electronics Forum | Sat Oct 08 23:17:14 EDT 2011 | peteralmendrala
Im a technician in smt specializing fuji cp6 series and juki 750 and 730. Know i wil be living my job and will move to other company specializing yamaha yv100. can somebody lend me a calibration and programming manual of this machine? Thanks in adva
Electronics Forum | Thu Mar 30 12:13:10 EST 2006 | Tech
Obviously you are not as experienced as you think so I will help you out a bit.You are correct on the size of the wrench. I was trying to recall from memory but the wrench size is 8mm. The odd size I recalled came from the other side of the wrench th
Electronics Forum | Thu Mar 30 07:41:44 EST 2006 | cyber_wolf
I do not reccomend spraying anything into those clutches. There is a greased bearing in there that cannot run dry. Also there is a very specific way to dismantle the clutches, and it does not require a 5.5 mm wrench in any part of it. Dax, if you
Electronics Forum | Wed Mar 08 23:40:43 EST 2006 | fastek
If......... 1) Assuming you are panelizing them (you would have to actually).... 2) You don't have any fine pitch parts on the board then I would suggest a chipshooter like a Fuji CP-6 or a Panasonic MV2F. Get (2) of these used for around $100K ea
Electronics Forum | Wed Apr 12 06:40:11 EDT 2006 | aj
All, I continuosly have reliability issues when placing a SOT363 device. I have Fuji CP6 and CP4 placement machines. The part data has been analysed down to the finest detail but it is still hard to maintain any consistency. Anyone else have simi
Electronics Forum | Wed Jun 23 10:26:53 EDT 2004 | exmaintenanceleader
Grant and all! CP-2 is the oldest fuji as I have been operated. CP-3 is built in 1989 as a new mc. Now 15 mc I now they runs in 3 shift widouth problems when they need countinous runing comes the problems. conroll card and relay contact problems at
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694