Electronics Forum | Wed Jul 14 13:41:40 EDT 2010 | rway
We are running SMT products and have been for some time now. First, I wanted to check with you folks to see what an acceptable FPY rate, or what you would consider and acceptable rate, is. Secondly, we are having issues primarily with product that
Electronics Forum | Sun Jul 25 08:54:37 EDT 1999 | Tom Gervascio
| We are having a process related problem with pullup resistors on a controller card which has a I960 micro-processor. | The controller monitors signal inputs and it's own resources then blinks a LED to indicate its working. The problem is that after
Electronics Forum | Mon Jul 26 14:14:51 EDT 1999 | Steve Gregory
| | | We are having a process related problem with pullup resistors on a controller card which has a I960 micro-processor. | | | The controller monitors signal inputs and it's own resources then blinks a LED to indicate its working. The problem is th
Electronics Forum | Mon Jul 26 10:25:12 EDT 1999 | Boca
| | We are having a process related problem with pullup resistors on a controller card which has a I960 micro-processor. | | The controller monitors signal inputs and it's own resources then blinks a LED to indicate its working. The problem is that a
Electronics Forum | Fri Jul 23 14:07:52 EDT 1999 | Carl J. Odle
We are having a process related problem with pullup resistors on a controller card which has a I960 micro-processor. The controller monitors signal inputs and it's own resources then blinks a LED to indicate its working. The problem is that after a p
Electronics Forum | Fri Jul 30 09:43:44 EDT 1999 | C.K.
| We are having a process related problem with pullup resistors on a controller card which has a I960 micro-processor. | The controller monitors signal inputs and it's own resources then blinks a LED to indicate its working. The problem is that after
Electronics Forum | Thu Nov 17 21:46:48 EST 2005 | C. Kolokoy
With DIP type components, a sub-par fluxing method (foaming a no-clean), and a chip wave where one is not needed are formulas for bridging and insufficient wetting. If you have SMD's on the wave solder side of the board greater than 0603, and no SOT
Electronics Forum | Thu Jun 26 13:24:25 EDT 2008 | realchunks
Do you glue SMT parts on the bottom? If so, use your SMT glue to prevent the short. Just cut a new stencil with 0.020" wide apertures between the pads of the connector (bottom side). We do it all the time.
Electronics Forum | Wed Jul 19 17:34:25 EDT 2000 | Deon Nungaray
Craig, I'd be really hesitant in pursuing this method for a TQFP. Remember, most SMD's are rated for a maximum rising slope of around 4C/Sec. Immersing a fragile TQFP in a hot wave of molten solder will probably exceed this ramp up rate. Besides thi
Electronics Forum | Sat Oct 07 04:02:50 EDT 2000 | C.J. Long
Good morning, All: I am from PCB shop and one of our customer is experiencing solder bridge on 16 mil pitch QFP( immersion gold finish). Land width requirement is 8 +/- 1 mil measured over top of of land and our mean is 7 mil. Bottom land width is 8
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang， Fuhai Street，Fuyong
Shenzhen, 30 China
Phone: 13713862102
