117 ipc twist warp results

Electronics Forum: ipc twist warp (Page 1 of 12)

warp and twist

Electronics Forum | Tue Feb 14 09:10:43 EST 2017 | davef

Assuming the traces run parallel and perpendicular to each other, I'd choose one direction the traces run as "x" and the other direction for "y." Then I'd pick a unique identifier on the board to insure proper orientation. Next, I'd measure warp and

warp and twist

Electronics Forum | Mon Feb 13 23:05:02 EST 2017 | swestheimer

I have been asked a very good question but have not been able to find a good answer. IPC for both PCB and PCBA refer to the X & Y dimensions to measure warp and twist but how would you determine the warp and twist for a round PCB or PCBA?

warp and twist

Electronics Forum | Tue Feb 14 22:20:10 EST 2017 | swestheimer

Hi Dave, Thank you for your inputs as they were good suggestions. I however let out one important detail and that this is IMS material and not glass reinforced so I think that there is more bending going on during processing than warping and twistin

Bow and twist of PCB's

Electronics Forum | Fri Apr 20 13:55:09 EDT 2001 | kawiederhold

Hey Dougie, If you go to IPC.ORG and click on the on-line resources and databases, then on the "free downloads" link, the second or third document "for free" is the IPC-TM-650 in its entirety. It does discuss the test you are looking for! Have fun

PCB assembly bow and twist

Electronics Forum | Thu Dec 26 12:12:55 EST 2013 | igorfo

Dear Friends, I need your help to understand requirements and measurement methods for bow and twist of assembled PCB (PCBA have and SMT and TH components). I already check all posts on the site but didn't found any related to my question answers.

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 14:03:18 EDT 2001 | Ryan Jennens

Dougie- We,too, have the IPC-A-600F, and the spec. refers to IPC-TM-650 test method in the back of the book. Look on page Number 2.4.22 of the test methods appendix. This outlines the procedure for determining the percentage of bow and twist,

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 11:44:55 EDT 2001 | CAL

650 Standards are also located in the back of IPC JSTD-001. I am currently looking at 4 pages on bow and twist. Percent bow = R1-R2/L x 100 (R1= Highest point; R2=lowest or resting point; l= length) Percent twist=(R1-R2)/(2xL)x 100 Sorry if this is

Bow and twist of PCB's

Electronics Forum | Fri Apr 20 07:12:22 EDT 2001 | wbu

Dougie, oh yes, it�s a bit short that chapter. I have the Revision e in front of me and this one contains in the appendix the needed IPC-TM-650 Test method for bow and twist. Can�t think that they don�t have that in the new revision. Hope you find

Bow and twist of PCB's

Electronics Forum | Fri Apr 20 05:32:39 EDT 2001 | dougie

Hi, I've just splashed out �60 on IPC-A-600F trying to find out the formula for measuring the bow and twist of raw PCB's. Much to my dismay there are 10 lines on the subject in the whole standard. Worse still is that it tells me nothing I don't alre

DoE on post-reflow PCB - warp

Electronics Forum | Wed Jun 26 08:53:32 EDT 2002 | davef

We have not done a DOE on board warping. Consider: * How close the board gets to its Tg during the reflow cycle * Amount of copper on each side and the balance between the two * Thickness of the board * Overall length x width * Time at temperature