Electronics Forum | Tue Jan 09 12:51:14 EST 2007 | aj
All, We have ran a few revisions of a New Product which is a tracking device using satellite navigation. The protos went well but now they have added a shielding can. We place 2 of these to cover the Frontend of the PCB. The test guys are having d
Electronics Forum | Thu Apr 05 13:54:18 EDT 2001 | CAL
Do the parts sit directly on the PCB? Typical 2.0 mm Max is desired for the component to be off the PCB. Are stand-offs an option? The long lead wiggles as it passes through the wave and thus agitating the air out.Does your wave a "dancer" option?
Electronics Forum | Thu Jun 26 09:30:24 EDT 2008 | gabriella
Hello, about 20mm - some kind of inductance for this week. If I were you, I would check another brands of ovens too. I mean why the clearance is so small and why they want to charge you for their mistakes? I would insist to do that for free. Next
Electronics Forum | Mon Sep 14 09:25:49 EDT 1998 | Dave F
0.050" -> 50 mil -> 50 pitch | 0.80 mm -> 0.032" -> 32 mil -> 32 pitch | 0.64 mm -> 0.025" -> 25 mil -> 25 pitch | 0.50 mm -> 0.020" -> 20 mil -> 20 pitch | 0.40 mm -> 0.016" -> 16 mil -> 16 pitch | 0.20 mm -> 0.012" -> 12 mil -> 12 pitch | Dave F Y
Electronics Forum | Wed Sep 26 17:26:02 EDT 2007 | jax
So far, So good! We are currently standardizing the Lightning Head Advantis as our chip-shooter. We only place chip packages, 0201-1206 with the Lightning Head and everything runs great. We performed qualification testing with components up to 20mm
Electronics Forum | Wed Oct 17 02:53:36 EDT 2001 | dszeto
The fine pitch QFP is a 240 pin one being loaded with other components on a 2.0mm thick FR4 PCB. There are 6 of this Qfp's on this PCB showing the same charactristic of bowing therfore the solder fillets are vary from the center to the end of the pa
Electronics Forum | Tue Aug 09 11:14:28 EDT 2016 | cyber_wolf
•Rated Speed of 40,000 CPH •140 - 8mm Device Locations •14" x 18" Max PCB Size PCB dimensions Max: 457mm x 356mm Min: 80mm x 60mm Board Thickness: 0.3 to 4.0mm Component capacity Up to 140 types (8mm tape) Placing rate 0.09 sec./component - 40,
Electronics Forum | Tue Jun 08 08:40:37 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Tue Jun 08 08:38:15 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Thu Jan 20 23:59:30 EST 2011 | jeffr
These machines have three heads... Head 1 (jaws 0.7mm x 4mm)0603 up to small tantalum. Head 2 (jaws 3.0mm x 20mm)small tant up to PLCC44 or SOP28. Head 3 No jaws, uses just Vision. Can do Large tantalum up to QFP208, however can only take a single no
