Electronics Forum | Thu Aug 12 14:17:19 EDT 2010 | mikesewell
You might reduce your panel size, cut it in half and rotate to better utilize your edge clamping/board supports. Tape off your current stencil and see if it improves the print. A new stencil and a little extra handling may be cheaper than tooling.
Electronics Forum | Thu Aug 12 11:00:42 EDT 2010 | hegemon
Without seeing a picture, my first instinct would be first and foremost some fixturing that provides full support for your print process. After that, since you are citing bow and twist, consider that the fixturing might as well travel through the ov
Electronics Forum | Wed Aug 11 18:35:17 EDT 2010 | julie1
Anyone work with or have knowledge about metal core/clad boards? The board I'm working with is approximately 2" X 3/4" aluminum core pcb, in a 56 up array. There are 3 LED placements per board. I'm having trouble getting a consistent screen print.
Electronics Forum | Tue Jan 03 11:30:13 EST 2012 | ppcbs
Try using Chip Quik to reduce the heat required for component removal. Along with your bottom pre-heater, use a temperature controlled hot air system to help heat up top side for component installation. http://www.pcb-repair.com/products.htm
Electronics Forum | Tue Jan 03 11:01:19 EST 2012 | julie331975
We are working with .065" thick metal core PCB's. I have a couple boards that are in need of rework. The components we are placing are similar to a SOJ package with a solder pad underneath the component. We are also using a lead free process. I have
Electronics Forum | Thu Jan 05 10:56:49 EST 2012 | davef
The high thermal mass of metal core boards makes them difficult to heat with hot air convection heating or IR. So, edge heaters are used for effective heating of heavy core circuit boards. Hakko and VJ Electronix offer edge heaters. We imagine othe
Electronics Forum | Mon Jul 12 14:00:37 EDT 2004 | blnorman
We've been using lasers to mark barcodes on our boards for some time now. We use a CO2 laser to burn through the solder mask on most of our boards. The machine is enclosed so the operators aren't exposed to the laser. The laser is also mounted on
Electronics Forum | Tue Nov 03 20:00:47 EST 2009 | davef
Solder Mask Adhesion Pull Test Tape List IPC-TM-650 Test Method 2.4.28.1, Adhesion, Solder Resist (Mask), Tape Test Method, defines the procedure for determining the adhesion of solder resists (masks) used over melting metals, (such as solder plated
Electronics Forum | Mon Aug 27 12:51:32 EDT 2012 | cobham1
I have run 0.031 boards. One of the things you may want to look at is the speed of the oven. With 14 zones you may be going to slow with the board which could be the reason your boards are starting to bow. You might also think about adding stiffners
Electronics Forum | Sat Apr 30 11:34:23 EDT 2016 | huanyupcb
High Mix,Low Volume,Short Delivery PCB Supplier. 1.The world top 500 PCB supplier.( Samsung DELL Alcatel-Lucent Huawei Lenovo FOXCONN ASUS etc ) 2.Over 15+ Years of PCB Expertise. 3.Provided "PCB & Assembly One-stop shop"service,No MOQ. 4.ISO9001 I
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
