Electronics Forum | Wed Aug 11 18:35:17 EDT 2010 | julie1
Anyone work with or have knowledge about metal core/clad boards? The board I'm working with is approximately 2" X 3/4" aluminum core pcb, in a 56 up array. There are 3 LED placements per board. I'm having trouble getting a consistent screen print.
Electronics Forum | Thu Aug 12 11:00:42 EDT 2010 | hegemon
Without seeing a picture, my first instinct would be first and foremost some fixturing that provides full support for your print process. After that, since you are citing bow and twist, consider that the fixturing might as well travel through the ov
Electronics Forum | Mon Feb 13 23:05:02 EST 2017 | swestheimer
I have been asked a very good question but have not been able to find a good answer. IPC for both PCB and PCBA refer to the X & Y dimensions to measure warp and twist but how would you determine the warp and twist for a round PCB or PCBA?
Electronics Forum | Fri Apr 20 13:55:09 EDT 2001 | kawiederhold
Hey Dougie, If you go to IPC.ORG and click on the on-line resources and databases, then on the "free downloads" link, the second or third document "for free" is the IPC-TM-650 in its entirety. It does discuss the test you are looking for! Have fun
Electronics Forum | Thu Dec 26 12:12:55 EST 2013 | igorfo
Dear Friends, I need your help to understand requirements and measurement methods for bow and twist of assembled PCB (PCBA have and SMT and TH components). I already check all posts on the site but didn't found any related to my question answers.
Electronics Forum | Mon Apr 23 14:03:18 EDT 2001 | Ryan Jennens
Dougie- We,too, have the IPC-A-600F, and the spec. refers to IPC-TM-650 test method in the back of the book. Look on page Number 2.4.22 of the test methods appendix. This outlines the procedure for determining the percentage of bow and twist,
Electronics Forum | Mon Apr 23 11:44:55 EDT 2001 | CAL
650 Standards are also located in the back of IPC JSTD-001. I am currently looking at 4 pages on bow and twist. Percent bow = R1-R2/L x 100 (R1= Highest point; R2=lowest or resting point; l= length) Percent twist=(R1-R2)/(2xL)x 100 Sorry if this is
Electronics Forum | Fri Apr 20 05:32:39 EDT 2001 | dougie
Hi, I've just splashed out �60 on IPC-A-600F trying to find out the formula for measuring the bow and twist of raw PCB's. Much to my dismay there are 10 lines on the subject in the whole standard. Worse still is that it tells me nothing I don't alre
Electronics Forum | Fri Apr 20 07:12:22 EDT 2001 | wbu
Dougie, oh yes, it�s a bit short that chapter. I have the Revision e in front of me and this one contains in the appendix the needed IPC-TM-650 Test method for bow and twist. Can�t think that they don�t have that in the new revision. Hope you find
Electronics Forum | Tue Nov 03 20:00:47 EST 2009 | davef
Solder Mask Adhesion Pull Test Tape List IPC-TM-650 Test Method 2.4.28.1, Adhesion, Solder Resist (Mask), Tape Test Method, defines the procedure for determining the adhesion of solder resists (masks) used over melting metals, (such as solder plated
IPC is the trade association for the printed wiring board and electronics assembly industries.
Training Provider / Events Organizer / Association / Non-Profit
3000 Lakeside Drive, 309 S
Bannockburn, IL USA
Phone: 847-615-7100