Electronics Forum | Wed Jun 03 14:37:53 EDT 1998 | Anthony
I really appreciate everybody taking the time to help me out with this problem. I'm going to run your input by the design engineer, after that I may be taking you up on that offer to contact you Earl. Again; thank you! Anthony | If your board is si
Electronics Forum | Tue Dec 16 16:14:20 EST 2003 | Bill
We are in need of a replacement conveyor belt for an unload-end conveyor(post wave solder). The part number we had at one point (formerly PCT automation) was 65-4008-4 (Belt, Flat-W=23.75 L=171.70) green high temp conveyor belt. Any help would be g
Electronics Forum | Sat Jun 17 09:09:15 EDT 2000 | Chrys Shea
Contact the adhesive manufacturer, or their website. Most adhesive suppliers offer two cure options - one with a belt oven profile and one with a box oven profile. The belt oven is usually a ramp and plateau of 120-150C for approx 2 minutes. The b
Electronics Forum | Tue Feb 02 10:18:56 EST 1999 | Justin Medernach
| I have a recent design (1 component side only) that calls for 2 surface mounted antenna's (brass plated) to be mounted on a PCB. The problem arises when the PCB is 18x11.25 and has 15 to 20 PCB's in the pallet (IE weight, fixturing to hold the ant
Electronics Forum | Mon Aug 22 09:01:09 EDT 2005 | iwan
Well guys, I just buy a brand new solder paste softener Malcom type SPS2, I've tried with this with this viscosity result. I Use Almit Solder Paste Lead Free LFM-52X 1 min : 264 pas. 2 min : 272 pas. 3 min : 277 pas. I use standard for Viscosity 20
Electronics Forum | Fri Dec 08 21:26:44 EST 2006 | billwestiet
You already have some good answers. A chemical isolation zone for RMA is a good idea. If you are looking for new see the two references you have and Austin America. If you are looking for used, see us at http://www.ietechnology.net. We presently
Electronics Forum | Tue Feb 16 13:57:50 EST 1999 | Ron Beasley
| | I have a recent design (1 component side only) that calls for 2 surface mounted antenna's (brass plated) to be mounted on a PCB. The problem arises when the PCB is 18x11.25 and has 15 to 20 PCB's in the pallet (IE weight, fixturing to hold the a
Electronics Forum | Mon May 11 17:35:01 EDT 1998 | Steve Gregory
On 11 May, 1998 Todd wrote: | We are having continuous bridging problems with the trailing | leads on a 26-pin D-sub through-hole connector. The pitch is | 0.100". The connector is going through the wave at approximately | a 20 Degree angle. Does
Electronics Forum | Wed May 19 20:39:28 EDT 2021 | kumarb
Elissa - SMTWenzhan ? She is great !! Have purchased many oddball and common parts from her including belts, filters, grease, etc. BTW - We placed 01005 using a nozzle she sold us with our Emerald-X. Unbelievable !! Granted the pick was hit or miss
Electronics Forum | Wed Jun 03 11:17:17 EDT 1998 | Brian Stumm
If your board is single sided you should convey it on a mesh belt conveyor. Unfortunately most assemblies these days are double sided which makes it difficult to convey on the mesh belt. Plus with the increasing population on SM boards the weight is
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694