Electronics Forum: mydata hydra tagedry problem (Page 1 of 5)

mydata 19 error

Electronics Forum | Thu Feb 13 00:43:06 EST 2014 | brendansales

Centering motor about to fail or has failed. > Centering motor about to fail or has failed. Hey Rdubya, Thanks for your help! Apparently that was not the problem. The Midas head had to be all the way down below the lower locking solenoid. After

mydata 19 error

Electronics Forum | Wed Feb 19 09:52:45 EST 2014 | brendansales

Dear Rob, Got to the maintenance menu, under the Motor section, I selected Z motor and tried to initiate motor, there was no movement on the machine and I had the error message as below: F-MOT-MSETDYN Z/12: Position counter dead I suspect that ser

used mydata equipment

Electronics Forum | Sat Jan 29 04:59:02 EST 2005 | Grant

Hi, MYDATA's are ok for lower volume, and they are very flexible. If you only have 1 or 2 trays of components and are on a tight budget, then you can even place the trays on the Y wagon behind the PCB so you can get away without the tray wagon. Al

Placing domed parts with mydata

Electronics Forum | Tue Feb 03 10:44:56 EST 2009 | lmartenson

We have been having problems placing a domed LED with a Mydata HYDRA. The pocket that the part comes in seems to have some slop causing the part to be picked crooked. We have been playing around with different custom tools. Has anyone had similar

Mydata sod523 pickup problem

Electronics Forum | Tue Mar 04 17:17:29 EST 2014 | catsem23

Hi I'm trying to pick and place a lot of sod523 components with a mydata my12. I'm using C14 standard tool and Hydra tool H01. For some reason no matter what I try to do when the head picks the component with the C14 tool the machine emergency stops

MYDATA - how to forse parts on Hydra head

Electronics Forum | Mon Dec 19 07:55:30 EST 2016 | bk

I am assuming that these are the round aluminum electrolytic caps. The problem may be that they are too wide to put on 2 hydra heads next to each other. Plus the hydra heads are not that great at placing tall parts. I would not let the hydra place th

MyData F-MOT MOVESLOWMOVE HYDRA error

Electronics Forum | Thu Mar 28 16:51:00 EDT 2024 | tey422

Since you only saying it's the hydra error, then only run the hydra calibrations. Sometime the calibration can end up causing more issue if not run it correctly. I would do the hydra camera Z level (1st). If it fixes the issue then you no need to do

Mydata Hydra tool reference marks error

Electronics Forum | Wed Jun 17 01:02:16 EDT 2015 | armandogomez

Hello Had a similar problem way back with the hydra, first go to the service program manually activate the hydra camera then move the Xwagon to place the hydra ref plate over the hydra camera and check first if the camera works, second the image you

Mydata Hydra tool reference mark error

Electronics Forum | Sat May 04 11:24:08 EDT 2013 | amelby

Hi, I have been having a problem with my My19E's hydra. The machine comes up with an error "Failed to locate HYDRA tool reference marks" and stops running. It does not happen for about the first two hours of running. It starts to happen after that an

Mydata (MY12) error-Frame Grab and Light Curtain

Electronics Forum | Sat Oct 03 07:26:01 EDT 2009 | cflames17

Check the reference plate on the hydra to make sure it is not cracked or delaminated. I have had problems with the glue coming loose and the plate flapping causing this same problem. check hydra camera calibrations, this to may help.

  1 2 3 4 5 Next

mydata hydra tagedry problem searches for Companies, Equipment, Machines, Suppliers & Information