Electronics Forum | Fri Jan 10 03:33:42 EST 2014 | hans88
hello people, we have a my12 wich has a problem it gives the following error during hardware initialization: F-MOT-MSETDYN Y/1236 :Motor amplifier channel a error. after this error it says hardware initialization failed. this prevents us of using
Electronics Forum | Sat Jan 29 04:59:02 EST 2005 | Grant
Hi, MYDATA's are ok for lower volume, and they are very flexible. If you only have 1 or 2 trays of components and are on a tight budget, then you can even place the trays on the Y wagon behind the PCB so you can get away without the tray wagon. Al
Electronics Forum | Tue Jan 23 17:22:45 EST 2024 | tomdegas
For some reason I cannot load any tools on my MY12 machine. The machine goes through the motions like its loading the tool (grabbing it and putting it back) but at the very end it moves the carriage all the way to the right and wants me to put the t
Electronics Forum | Thu May 26 12:21:04 EDT 2005 | stepheniii
We have dek-my12-my12-heller. We are very happy with it. Change-over time varies more by facility than by machine type. I worked at a place with dek-mviif-msf-btu and we had faster changeovers there. There we had a dedicated feeder set-up. Close to
Electronics Forum | Fri Jul 31 12:53:58 EDT 2009 | dyoungquist
On our Mydata machine, we place a piece of scrap bare pcb next to the pcb we are loading. Using double sided tape, we attach the cut tape strip to the bare pcb, then program the machine to pick up the parts from that location. The smallest Mydata m
Electronics Forum | Tue Nov 15 23:03:07 EST 2011 | supse
Hi I have a problem with one of our MY12 machines, the machine stops very often (approx. 10-20 times a day) writing the following error message : f-mot-msetdyn hydra theta/205(f-hrdw-3). We then have to reinitialize the machine to continue productio
Electronics Forum | Mon May 06 14:55:58 EDT 2013 | dyoungquist
We had that problem on our M12. There were a few components that had gotten dropped into the camera area as the hydra head past over it. Our MY12 has a knob towards the front of the machine in direct line with the camera. Pulling this knob release
Electronics Forum | Fri Mar 24 05:07:03 EDT 2023 | smtusa
On average year how much problems did you have with mychronic? They have some features that are appealing to me that other manufacturers don't do: front feeder loading system, fit through a 36" door, no air compressor make it desirable for offi
Electronics Forum | Fri Sep 25 13:09:42 EDT 2009 | rmitchell
Thanks to those that responded. I eliminated the light curtain problem. The metal plate the light curtain pcb bolts to was bent. I had it aligned in our machine shop and it worked properly. I forgot to mention the error was pooping up with no fee
Electronics Forum | Fri Sep 09 05:42:43 EDT 2016 | jasltd
Hi folks, I'm looking for definitions on the categories from the Management reporting from MYData's (running My9 & MY19 machines TPSYS 2.4) I'd like to understand what the machine classifies into the following: Up time Active Time Run Time I"m buil
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
.gif)
