Electronics Forum: mydata z motor timeout (Page 1 of 5)

Mydata My9 X MOT motor timeout

Electronics Forum | Sun Jun 12 01:38:47 EDT 2022 | mikevb

I'm having a problem with my Mydata My9 pick and place. Basically whenever I try to run the placement calibration program or try to have the machine find fiducials, or basically anything with precision, the machine displays a X MOT motor timeout erro

Mydata My9 X MOT motor timeout

Electronics Forum | Wed Jun 15 19:46:15 EDT 2022 | mikevb

Hey All. I figured it out. It turns out that the problem was simply a loose coupler on the x wagon motor transducer. I had only checked one screw in the past but the other screw was apparently loose as well.

Mydata My9 X MOT motor timeout

Electronics Forum | Sun Jun 12 01:44:59 EDT 2022 | mikevb

I forgot to mention that I've measured and adjusted the cog play on the x axis and so it is within range, if that applies.

Mydata My9 X MOT motor timeout

Electronics Forum | Tue Jun 14 15:59:25 EDT 2022 | mikevb

Thanks! I just needed a response like that. I will do all that, and if it's still an issue, I'll change the x wagon encoder right? There are three encoders on the x wagon though? The white one on the x carriage, the white one on the x belt drive mo

Mydata My9 X MOT motor timeout

Electronics Forum | Tue Jun 14 15:02:13 EDT 2022 | glasscake

Start with fundamentals: Disconnect, clean and reconnect all inner connections, bulk heads, ext. Disconnect, reconnect all connections at the controller. Check wiring harness for conductivity. Clean everything appropriately, lube ways, balls screws

Mydata My9 X MOT motor timeout

Electronics Forum | Tue Jun 14 16:23:22 EDT 2022 | glasscake

Cant put a finger on it being an encoder that was just a single possibility. You can always hook up a scope to the encoder and see if they are working appropriately. I would look through the machine's utilities and see if there is some debug or more

mydata 19 error

Electronics Forum | Wed Feb 19 09:52:45 EST 2014 | brendansales

Dear Rob, Got to the maintenance menu, under the Motor section, I selected Z motor and tried to initiate motor, there was no movement on the machine and I had the error message as below: F-MOT-MSETDYN Z/12: Position counter dead I suspect that ser

mydata 19 error

Electronics Forum | Thu Feb 20 13:16:15 EST 2014 | rgduval

Hi, Brendan, It sure sounds like it to me. But, with the Z axis, there could be one other thing to check. On my old TP, there were z-locks...two pistons that pointed sideways around the head travel. Initializing the z-motors did not move the z-

mydata 19 error

Electronics Forum | Thu Feb 13 00:43:06 EST 2014 | brendansales

Centering motor about to fail or has failed. > Centering motor about to fail or has failed. Hey Rdubya, Thanks for your help! Apparently that was not the problem. The Midas head had to be all the way down below the lower locking solenoid. After

mydata 19 error

Electronics Forum | Thu Feb 13 09:52:03 EST 2014 | rgduval

Start by getting into the maintenance menu, and manually installing the Servo program for all MOTs. If they install fine, you can check the Z-motor while you're in the maintenance menus. Make sure that the z-locks are unlocked before checking the

  1 2 3 4 5 Next

mydata z motor timeout searches for Companies, Equipment, Machines, Suppliers & Information

Win Source Online Electronic parts

Software for SMT placement & AOI - Free Download.
Circuit Board, PCB Assembly & electronics manufacturing service provider

Best Reflow Oven
PCB separator

Internet marketing services for manufacturing companies