Electronics Forum | Fri Oct 08 17:12:31 EDT 1999 | Dave F
| Hi, | | Does anybody know what is the minimum gold plating thickness on the PCB goldfinger required by the industrial specifications - IPC, Bellcore, etc. Where can I find the information? Appreciate for the help! | | Thanks, | Tony | Hi Tony:
Electronics Forum | Mon Aug 16 20:32:10 EDT 2004 | davef
First, we didn't say "electrolytic soft gold with a minimum thickness of 5-8 of Au". We said, "'electrolytic soft gold' thickness 5 to 8uin". FOCUS. ;-) Second, we're unaware of an industry accepted specification that you can reference. IPC-2221
Electronics Forum | Wed Aug 11 18:36:03 EDT 2004 | davef
90 Knoop. Q2: Thickness is 4 to 10 u" for Au and 300 to 400 u" for nickel A2: This looks like a ENIG spec. Although, the Ni is quite heavy, 150 uin is sufficient for most applications. [IPC-4552 ENIG specification: * Gold thickness of 0.075 - 0.125
Electronics Forum | Thu Oct 07 20:34:48 EDT 1999 | Tony Huang
Hi, Does anybody know what is the minimum gold plating thickness on the PCB goldfinger required by the industrial specifications - IPC, Bellcore, etc. Where can I find the information? Appreciate for the help! Thanks, Tony
Electronics Forum | Mon Aug 16 16:37:08 EDT 2004 | davef
As we mentioned in an earlier response in this thread [Q5], you do NOT want to solder to hard gold. Hard gold is a wear surface. [That's IT, that's the LIST.] If you want to solder to gold, then either use: * IPC-4552 ENIG specification, mentioned
Electronics Forum | Mon Oct 27 20:01:00 EDT 2014 | rangarajd
Hello, We are facing solderability issues on a particular lot of board. THe Nickel thickness measured with an XRF is around 400 U inches. Spec calls out for 130 u inches Nickel and 3 - 5 U inches gold over it. Assuming there is no porosity on the g
Electronics Forum | Tue Jul 15 16:30:57 EDT 2008 | boardhouse
Hi Aj, Recommended Immersion gold thickness would be 3-5 Micro inches over 140 -200 micro inches of Nickel. Thicker Immersion gold than 5 micro inches can cause solder joint embrittlement. Gold readily dissolves in molten solder and will be present
Electronics Forum | Wed Aug 11 16:09:50 EDT 2004 | Kris
Hi How does one distinquish between hard gold and immersion gold ? thickness is 4 to 10 u" for Au and 300 to 400 u" for nickel what happens if the gold drops below 3" and the nickel is above 350" what are the typical failure modes associated with
Electronics Forum | Mon Aug 16 13:18:46 EDT 2004 | davef
You bet our reponse changes. Q2R: Hard gold thickness is 4 to 10 u" for Au and 300 to 400 u" for nickel A2R: This is a hard gold spec?? It looks like a ENIG spec. Although, the Ni is quite heavy, 150 uin is sufficient for most applications. The gol
Electronics Forum | Fri Feb 24 11:31:20 EST 2012 | pauld
I need to be sure of the Nickel/Hard Gold thickness to be specified on our drawing. We use hard gold on a slip ring pcb that has brushes riding over the conductive surface, so soldering is not the issue. I read through the hard gold vs immersion gold
Buy and selling used smt,semi, Robot ,CNC and all used machines
Equipment Dealer / Broker / Auctions
DONGGUAN HUMEN
Dongguan, 30 China
Phone: 13560819457