Electronics Forum: nxt head h04 (Page 1 of 4)

NXT head H04 placing problem

Electronics Forum | Mon Jan 28 03:00:24 EST 2019 | nikevoo1

The problem was in mechanical valve O-rings. I replaced the valves and the problem disappeared.

NXT head H04 placing problem

Electronics Forum | Tue Jan 22 20:39:04 EST 2019 | nikevoo1

Hello, The problem is with NXT head H04. So there are 4 nozzles that take elements and place them on the PCB.The problem is that it does not randomly place the already taken element on the PCB.The nozzle take element and going to place it, but does't

NXT head H04 placing problem

Electronics Forum | Wed Jan 23 18:57:09 EST 2019 | nikevoo1

Is it possible to have too much grease on mechanical valves and because of that something has been clogged? Or mechanical valve O-rings to be a problem? https://imgur.com/a/ZHShMAH https://imgur.com/a/SzAWIL0

NXT head H04 placing problem

Electronics Forum | Wed Jan 23 11:14:11 EST 2019 | assuredtech

Do you have a spare head? or have you tried swapping the head to a different module? Is it always the same component (element)? Inspect the component under a scope / perhaps a packaging / adhesive issue. If the component is staying on the nozzle what

NXT head H04 placing problem

Electronics Forum | Wed Jan 23 12:49:44 EST 2019 | nikevoo1

next step, if the nozzle have to take the same component, the nozzle is going to take it and the both components stick together(one over the other) and the nozzle places them like this stick together. So there is nothing in one place, and on another

NXT head H04 placing problem

Electronics Forum | Wed Jan 23 20:01:20 EST 2019 | padawanlinuxero

Hello Sounds to me that the problem might be with vaccum and lot of it, after the component is place theres a small amount of air that pushes the component away from the nozzle in MYDATA we call it a kiss in my facility, have you check that the air

NXT head H04 placing problem

Electronics Forum | Wed Jan 30 00:56:00 EST 2019 | kiransahu

Sounds to me that the issue may be with vacuum and part of it, after the segment is put there's a little measure of air that pushes the segment far from the spout in MYDATA we consider it a kiss in my office, have you watch that the air that "puffs"

Samsung SM320 VS Assembleon 8 head Opal XII

Electronics Forum | Fri Dec 16 06:39:15 EST 2005 | rlackey

I know that you were very specific in your email about your choices, but have you not thought of adding a faster Mydata? You would negate the learning curve on operations & maintenance, have spare feeders, & be able to transfer programs over. Regard

Flason SMT Products

Electronics Forum | Thu Oct 04 00:01:59 EDT 2018 | gaintstar

Flason SMT FUJI Pick and Place Machine: http://www.flason-smt.com/product/FUJI-Chip-Mounter-SMT-spare-parts-A10395-Fiber-Amplifier.html http://www.flason-smt.com/product/FUJI-Chip-Mounter-SMT-spare-parts-Amplifier-A1038t.html http://www.flason-smt.co

Fuji Aimex or NXT II

Electronics Forum | Thu Feb 17 08:56:13 EST 2011 | zavalko

Hi! Our company is Fuji's distributor in Russia. AIMEX couldn't be much faster than NXT2. There are four heads limit in the AIMEX while NXT can have dozens of modules & heads in single machine. It's hard to get a field data on AIMEX. Machine was re

  1 2 3 4 Next

nxt head h04 searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

High Precision Fluid Dispensers
Sell Used SMT & Test Equipment

High Throughput Reflow Oven
All Surplus Auction - December 18, 2024

Best Reflow Oven
PCB Handling with CE

We offer SMT Nozzles, feeders and spare parts globally. Find out more
Voidless Reflow Soldering

Component Placement 101 Training Course
PCB Depanelizers

"Heller Korea"