Electronics Forum: offset printing machine cards (Page 1 of 8)

DEK Screen printer calibration - print offset issue

Electronics Forum | Thu Mar 30 10:02:03 EDT 2017 | Bestglobal SMT

We have a 2008 DEK horizon 03i this machine has been a very reliable system. we are having an issue with the print being offset in the x .2mm I have run 4 different boards - same issue on all. same offset. i can print the board 10 times over and

Volume and average height of solder paste after printing machine

Electronics Forum | Thu Oct 02 12:22:26 EDT 2008 | JerryS

Hello Ok there is not much info here. What you have to mae sure of is several key factors. 1. Have you entered the correct stencil thickness. 2. Are you using the stencil gerber (not the paste layer) The paste layer is usually not adjusted for ap

Re: Screen printing the board from........

Electronics Forum | Fri Mar 06 10:30:46 EST 1998 | Ron Costa

| | | Hello everyone! | | | Does any know anything about bare board size variations? | | | Is there a spec. or tolerance? | | | I'm running small lots of boards and during the screen printing process | | | I find that I cannot paste each board perfec

small and good pick and place machine

Electronics Forum | Thu Sep 05 23:18:03 EDT 2013 | feiyangniao

There is a new toy I received today: a NeoDen TM-240A automatic desktop pick and place machine! I’ve kept my eyes on this baby for a quite a while, and finally decided to make a purchase last week. The shipping was very fast: DHL from China, a total

DEK265 GSX misprint

Electronics Forum | Fri Oct 11 03:06:00 EDT 2019 | bukas

Hello Dekhead, it is a constant offset, like 0.5 mm to right when machine prints away from operator. When print goes towards the operator there is no offset. I swapped X5 and X6 cards with spares I got but still same result . I set the program to hav

Fuji CP642 Auto Pick adjust

Electronics Forum | Fri Jun 22 11:02:13 EDT 2007 | gregf912

I have a CP642E machine that will not function if auto adjust is enabled in Part Descriptor. Symptom: Auto pick offset causes machine to pick part off center to the point of going to end of part after several picks. This only happens to parts that ha

Quad oven-Need "offset.exe" s/w to calibrate temperature offsets

Electronics Forum | Tue Oct 06 14:29:14 EDT 2015 | cadco

Update 6 Oct 15: We have completely re-configured the oven PID boards such that everything is now visible on the oven by the s/w and all is now OK since the "Machine"card is now recognized. We have just one additional procedure to do and that is to

GSM Calibration; Z-axis not touching down to pickup calibration card.

Electronics Forum | Tue Jul 19 00:34:36 EDT 2022 | ttheis

We found that the "Z offset" on the head was altered relative to the other machine and restoring defaults made both machines display the same settings. Once defaults were restored for the second machine, it began picking up the card from the tray and

MPM Accuflex Calibration

Electronics Forum | Fri Jan 04 15:20:04 EST 2013 | dontfeedphils

Any idea where the global offsets are entered? Under the vision setup there are print offsets, but these seem like they would be program specific, which is something we're looking to avoid since we will be running two machines networked. Thanks for

MPM UP2000

Electronics Forum | Wed Sep 30 06:22:23 EDT 2015 | mervin

MPMENG, Thank you so much for taking the time to help. The machine has Y snuggers and flippers. The Pcb is loading in the center all the time. The driver cards look fine there is no obvious faults on them or partially burned. The machine was not in

  1 2 3 4 5 6 7 8 Next

offset printing machine cards searches for Companies, Equipment, Machines, Suppliers & Information

Sell Used SMT & Test Equipment

High Precision Fluid Dispensers
Electronic Solutions

High Throughput Reflow Oven
Best SMT Reflow Oven

World's Best Reflow Oven Customizable for Unique Applications
Hot selling SMT spare parts and professional SMT machine solutions

Thermal Transfer Materials.