Electronics Forum: ohm (Page 1 of 16)

marking standard for .1% resistors?

Electronics Forum | Mon Sep 18 14:43:06 EDT 2006 | jdengler

Steve, I don't think it was a Yageo if the value is 10 ohms. Yageo would label them as 10R0 for 10 ohms. 1002 would be a 10K ohm resistor. Jerry

Quad IVc Main Breaker

Electronics Forum | Tue May 07 15:30:41 EDT 2013 | bobpan

your card is probably bad.....you can ohm out the motor and cable if you want... z motor windings 1.36 ohms z motor cable and windings 1.82 ohms good luck

Conductive carbon inks for keypads, what specifications? IPC standard?

Electronics Forum | Tue Apr 06 12:13:46 EDT 2021 | luca

Hello, does anyone know if there is an IPC standard for carbon ink? we use for keypads instead ENIG, we found batchs of PCB with 2-3ohm, 20ohm, until 300ohm( resistance of contact surface) by the same PCB supplier!

SMT resistors

Electronics Forum | Tue Jun 06 10:48:47 EDT 2006 | jsloot

Perhaps there is someone who can answer this question. If a 1k 1% 0805 ohm resistor is missing a corner is it still going to read 1K ohm? Or, if it has an extra bit of material is it going to read more than 1k ohm? I am guessing that when chip reisis

Deionized Water Standards

Electronics Forum | Fri Feb 06 08:22:32 EST 2009 | davef

Conductivity is the recprical of resistivity. So, ... * 10 uS = 100k ohm * 5 uS = 200k ohm * 2 uS = 500k ohm We're unsure of the units of your conductivity of "1,566 uS/cm". Also, is that one thousand, five hundred, sixty six?

What is the std Resistivity for DI water at Aqueous

Electronics Forum | Tue Jul 31 13:55:27 EDT 2001 | mparker

Maintain DI water to 18 Meg Ohms resistivity. You can go down as low as 2 Meg ohms, in a pinch, but I would caution on what type of board you are running if trying to clean on 2 Meg ohm. Anything that is running an RF or high frequency circuit could

ohms reading

Electronics Forum | Thu Jan 03 21:43:20 EST 2002 | davef

Resistivity [1/ohm] readings are determined by the "cleanliness" that you desire to ensure the proper performance of your product. Check the fine SMTnet Archives for background. Contact USFilter [ http://www.usfilter.com/ ] for help.

Polar Instruments ToneOhm 950

Electronics Forum | Wed Nov 29 14:58:42 EST 2006 | eds

Does anyone have or know of a Polar Instruments ToneOhm 950 Short Locator, that they are willing to part with? Please advise.

0 Ohm SMD resistor

Electronics Forum | Sun Feb 12 03:06:04 EST 2012 | dan_ems

Please help me with this: I need a zero Ohm SMD resistor (strap) to connect 2 PCBs but to be like a wire, that can be bent. I need to be SMD because I want to be place it with "pick and place machine". Thank you.

Ceramic Inks

Electronics Forum | Tue Sep 28 17:23:21 EDT 2004 | davef

We use "0" ohm resistors a links. Is that what you're talking about?

  1 2 3 4 5 6 7 8 9 10 Next

ohm searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Throughput Reflow Oven
Voidless Reflow Soldering

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
PCB Handling with CE

Component Placement 101 Training Course
Fluid Dispensing, Staking, TIM, Solder Paste

Software for SMT placement & AOI - Free Download.
PCB Depanelizers

"Find out how you can receive priority in SMTnet Search with out Sponsor membership."