Electronics Forum: pad crater (Page 1 of 1)

pad cratering

Electronics Forum | Wed Jul 01 13:17:39 EDT 2015 | davef

Cheryl Tulkoff and Randy Schueller do a good job summarizing the thinks on pad cratering here: http://www.smta.org/chapters/files/uppermidwest_padcratering.pdf Potential Mitigations to Pad Cratering * Board Redesign * Solder mask defined vs. non-s

pad cratering

Electronics Forum | Wed Jul 01 04:54:28 EDT 2015 | jvercamm

hi, the last post on pad cratering dates from 2012. We have (likely similar) problems with a RoHS 783 solder ball BGA size 29x29mm^2 (organic package BT), pitch is 1mm and solder ball diam is 0.5mm the field failure is after 12 months, almost exclu

BGA Pad Cratering

Electronics Forum | Fri Jun 05 17:36:39 EDT 2009 | gsala

what do you think about Moisture entrapped into BGA or PCB before reflow ? regards GSx

BGA Pad Cratering

Electronics Forum | Fri Jun 05 16:06:51 EDT 2009 | mjz289

This is from a section of an ALtera EP2SGX130-5 STRATIX 2 leadfree 1,508 ball BGA. What can be causing this? It is from an unused board (not assembled in a unit, or in the field, but it did pass electrical and function test. There are three of them i

Pad cratering

Electronics Forum | Mon Jul 23 14:39:11 EDT 2012 | hegemon

I would think that wave solder beneath a BGA component might be a little bit stressful. The board will be expanding much faster than the BGA on the topside. This will cause some stress to the solder joints that might show up as the failure you are

BGA Pad Cratering

Electronics Forum | Sun Jun 07 09:01:47 EDT 2009 | davef

IPC T-50, Revision H, Terms and Definitions for Interconnecting and Packaging Electronic Circuits, 96.2176 Pad Cratering. A separation of the pad from the printed board resin/weave composite or within the composite immediately adjacent to the pad as

Pad cratering

Electronics Forum | Mon Jul 23 05:40:58 EDT 2012 | franks

We are having a problem with a 601 pin BGA in that the corners of the BGA are lifting and taking the pads with them. Faults are not always seen straight away so we are not sure at which point the fault is happening. So far it looks as though flexing

BGA Pad Cratering

Electronics Forum | Sat Jun 06 15:11:17 EDT 2009 | ysutariya

Was this a lead-free capable material that fits into IPC 4101/126 or /129, like an Isola 370HR? I would not be surprised because from the picture I think I can see resin underneath the lifted copper, which is an interlaminate separate. This is a

Au Wire bonding failure

Electronics Forum | Fri Dec 16 13:37:52 EST 2016 | edhare

Hi all, > > Recently, we are trying to do > wire bonding between a 75 * 75 um pad on a chip > and substrate with 150 um height difference, but > when completing wire bonding and the wire bonds > on pad and substrate, the pad will get out of

aluminium wire bonding on Electroless Nickel + Immersion gold

Electronics Forum | Mon Aug 27 15:06:29 EDT 2001 | davef

This otta push Wolfgang over the top ... Recommended reading G.G. Harman, Wire Bonding in Microelectronics : Materials, Processes, Reliability, and Yield, 2nd edition, McGraw-Hill Electronic Packaging and Interconnection Series, 1997. G.G. Harman, R

  1  

pad crater searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

Smt Feeder repair service centers in Europe, North, South America
Circuit Board, PCB Assembly & electronics manufacturing service provider

We offer SMT Nozzles, feeders and spare parts globally. Find out more
Circuit Board, PCB Assembly & electronics manufacturing service provider

High Precision Fluid Dispensers
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

Wave Soldering 101 Training Course
Fluid Dispensing, Staking, TIM, Solder Paste

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.