Electronics Forum: panasonic am100 tray machine (Page 1 of 2)

56mm feeders for Panasonic MPA P&P machine

Electronics Forum | Thu Sep 19 14:25:30 EDT 2002 | stepheno

Changing the pitch on the newer feeders is a little bit different and involves adjusting the location of a sensor. Where we lose the parts is at change-over. There are some reels that we might put on and take off a feeder 20 times before the reel is

Help finding a high capacity pick and place machine

Electronics Forum | Mon Mar 18 09:04:46 EDT 2024 | carl_p

Sounds like your talking very low volume & component counts really... I would look at Panasonic AM100 for example - low cost, high flexibility but you would need multiple so you could pair it with another... Ideally we would need to understand your

Help finding a high capacity pick and place machine

Electronics Forum | Mon Mar 18 08:48:58 EDT 2024 | spoiltforchoice

200 unique components across an entire range is nothing, Were we all so lucky we would all leave the inventory permanently loaded on the line. The Manncorp machines are probably your cheapest solution new. These chinese machines with western input

Panasonic AM100 vs other Pick & Place

Electronics Forum | Thu Apr 04 09:16:10 EDT 2024 | ianphil

Hi all, looking for some advice. We are in the market for some new pick and place machines and have had a quote for an AM100 from Panasonic. We are looking for flexibility and the ability to handle 0201 inch, all of which this machine seems to be abl

Panasonic vs Siplace which one better?

Electronics Forum | Thu Aug 25 03:09:32 EDT 2016 | buckcho

Hi,going to buy a new pick and place,any advise? > AM100 (Panasonic) vs e series (siplace). I think > both spec is quite similar. > > Thanks in > advance. It is very important to know what are you going to use them for. Selecting such machine

Panasonic AM100 vs other Pick & Place

Electronics Forum | Thu Apr 04 11:31:30 EDT 2024 | spoiltforchoice

With older machines you need to know their service history and working hours. Plenty of 10+ year old machines have done very little work and could easily do another 10 years the same. Other have worked non-stop on multi-shift lines, if something expe

Nozzle gives vacuum error

Electronics Forum | Sat Mar 11 07:33:52 EST 2023 | klauss

There's two kind of nozzles with different dimensions we use. One of them works good but the another one gives a head problem sometimes. The head picks the nozzle and gives the vacuum error despite the camera recognize it. So i make another head pi

Flason SMT Products

Electronics Forum | Thu Oct 04 00:03:28 EDT 2018 | gaintstar

flason smt pick and place machine: http://www.flason-smt.com/product/Hanwha-IC-placer-SM321-High-Speed-SMT-Modular-Chip-Mounter.html http://www.flason-smt.com/product/Hanwha-Pick-and-Place-Machine-DECAN-F2-High-Speed-SMT-Modular-Chip-Mounter.html htt

Tube Feeders For A Panasonic MPAG-3

Electronics Forum | Fri May 17 09:41:39 EDT 2002 | pteerink

Save your money. I tried to buy one for a G3 before, had one actually shipped in, and had to return it because it didn't fit the machine. Some other options: 1) buy a tape and reel machine cost you about $10K, but then you have control over

Matrix Trays

Electronics Forum | Fri Aug 19 15:45:45 EDT 2005 | DannyJ

I usually like to have all the trays use pin 1 in a certain direction. In other words, as you are on the operating side of the machine, all the pin 1's should be on the lower left of the tray. With operators, the KISS principle seems to be necessar

  1 2 Next

panasonic am100 tray machine searches for Companies, Equipment, Machines, Suppliers & Information

Electronic Solutions

Stencil Printing 101 Training Course
2024 Eptac IPC Certification Training Schedule

Wave Soldering 101 Training Course
Software for SMT

World's Best Reflow Oven Customizable for Unique Applications


"回流焊炉"