Electronics Forum | Wed Jun 03 14:37:53 EDT 1998 | Anthony
I really appreciate everybody taking the time to help me out with this problem. I'm going to run your input by the design engineer, after that I may be taking you up on that offer to contact you Earl. Again; thank you! Anthony | If your board is si
Electronics Forum | Tue Dec 16 16:14:20 EST 2003 | Bill
We are in need of a replacement conveyor belt for an unload-end conveyor(post wave solder). The part number we had at one point (formerly PCT automation) was 65-4008-4 (Belt, Flat-W=23.75 L=171.70) green high temp conveyor belt. Any help would be g
Electronics Forum | Sat Jun 17 09:09:15 EDT 2000 | Chrys Shea
Contact the adhesive manufacturer, or their website. Most adhesive suppliers offer two cure options - one with a belt oven profile and one with a box oven profile. The belt oven is usually a ramp and plateau of 120-150C for approx 2 minutes. The b
Electronics Forum | Tue Feb 02 10:18:56 EST 1999 | Justin Medernach
| I have a recent design (1 component side only) that calls for 2 surface mounted antenna's (brass plated) to be mounted on a PCB. The problem arises when the PCB is 18x11.25 and has 15 to 20 PCB's in the pallet (IE weight, fixturing to hold the ant
Electronics Forum | Mon Aug 22 09:01:09 EDT 2005 | iwan
Well guys, I just buy a brand new solder paste softener Malcom type SPS2, I've tried with this with this viscosity result. I Use Almit Solder Paste Lead Free LFM-52X 1 min : 264 pas. 2 min : 272 pas. 3 min : 277 pas. I use standard for Viscosity 20
Electronics Forum | Fri Dec 08 21:26:44 EST 2006 | billwestiet
You already have some good answers. A chemical isolation zone for RMA is a good idea. If you are looking for new see the two references you have and Austin America. If you are looking for used, see us at http://www.ietechnology.net. We presently
Electronics Forum | Tue Feb 16 13:57:50 EST 1999 | Ron Beasley
| | I have a recent design (1 component side only) that calls for 2 surface mounted antenna's (brass plated) to be mounted on a PCB. The problem arises when the PCB is 18x11.25 and has 15 to 20 PCB's in the pallet (IE weight, fixturing to hold the a
Electronics Forum | Mon May 11 17:35:01 EDT 1998 | Steve Gregory
On 11 May, 1998 Todd wrote: | We are having continuous bridging problems with the trailing | leads on a 26-pin D-sub through-hole connector. The pitch is | 0.100". The connector is going through the wave at approximately | a 20 Degree angle. Does
Electronics Forum | Wed May 19 20:39:28 EDT 2021 | kumarb
Elissa - SMTWenzhan ? She is great !! Have purchased many oddball and common parts from her including belts, filters, grease, etc. BTW - We placed 01005 using a nozzle she sold us with our Emerald-X. Unbelievable !! Granted the pick was hit or miss
Electronics Forum | Tue Mar 12 10:16:05 EDT 2013 | bocci572
Yes the components are flat and no larger than 50mm in size. Most are full rings or just an arc of a ring. I understand fully the best way to have the capabilities proven would be to have the vendor demonstrate. I am kind of looking at what people
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang, Fuhai Street,Fuyong
Shenzhen, 30 China
Phone: 13713862102