Electronics Forum: panasonic wave solder out feed conveyor (Page 6 of 12)

Wave Soldering Thick PCBs - Foam vs Spray Fluxing

Electronics Forum | Tue Dec 28 09:21:22 EST 2004 | pjc

In almost every application an ultrasonic spray fluxer will out perform foam fluxing. Better soldering results are what most expereince after making the change to U/S spray. There are good ultrasonic units from USI and Sono-Tek. www.ultraspray.com w

OT: Wavesolder Process Engineer Needed

Electronics Forum | Mon Jul 14 15:25:52 EDT 2008 | patrickbruneel

CK, If the contact length with the wave is decreasing when decreasing the conveyer speed and visa versa you need to check the machines electrical or electronics something is very wrong. Contact length is determent by wave design, wave height, convey

Re: Wave Solder Profiling Basics

Electronics Forum | Fri Jun 25 12:01:49 EDT 1999 | Earl Moon

| | Dear John/Earl | | | | Thanks for your clarifications. To me also the problem does not seem to be linked with the PCB. The Pre heater temp. is set at | | 450 degree C. We are using Alpha Aq. cleanable flux. Can you elaborate on the Desired

Brush-Up Your Intermetalics!!!

Electronics Forum | Thu Jun 17 21:31:06 EDT 1999 | Dave F

| | Does anyone know where I can find a list of things to do to when troubleshooting issues during the wave solder process? | | | | for example: | | | | Solder Bridge | | 1.verify amount of flux been aplied. | | 2.verify turbulance on your solder w

Selective Wave soldering machine

Electronics Forum | Tue Oct 20 19:26:10 EDT 2009 | fdbittner

I think machine selection depends upon your application (pitch, volume, changeover from pb to pb free etc...) I have experience with ERSA and Pillarhouse Jades. Both very good in their own right. Pillarhouse are relatively cheap, and quick to chan

SMT on Flexible circuits

Electronics Forum | Thu Feb 15 08:34:50 EST 2007 | rgduval

Jim, In a previous life, we built some flex circuits for a customer. The configuration was a flex cable, with a circuit at one end of it. We had fixtures made out of the same material that we had selective wave solder fixtures made from. Cut an i

Inline Washers

Electronics Forum | Tue Mar 11 18:01:26 EST 2003 | russ

Tim, I cannot remember what model our T.D. wave was it was a small unit about 8 ft. long "tabletop" is what I call them. In keeping up with this thread I noticed a lot of T.D. support. So, I decided to backtrack and review history with my previous pe

Re: VOC Free Flux

Electronics Forum | Fri May 14 16:24:35 EDT 1999 | Chrys Shea

| | I am looking for anyone who has converted over to VOC Free flux. I need some info on any problems, etc. that you might have had. | | | | Please E-mail me at wes.ruggles@vickers-systems.com or call at (513) 494-5229 | | | | Thanks | | Wes Ruggl

Paste In Hole

Electronics Forum | Thu Jun 28 10:58:28 EDT 2001 | brownsj

The question is are you talking of a reflow or wavesolder process. If your talking reflow I used to use a stepped stencil to ensure I had sufficient paste and then make a double pass with my squeegees. First pass with a 45 degree rubber squeegee to f

Re: Top Side BGA Reflowing @ Wave Solder

Electronics Forum | Fri Oct 08 16:36:28 EDT 1999 | Glenn Robertson

| We've recently encountered this problem where one of our .050" pitch BGA's were reflowing at the wave thus causing shorts... The board was profiled with probes stuck to a QFP solder joint, an 0603, and one of the BGA joints. There was an almost 7


panasonic wave solder out feed conveyor searches for Companies, Equipment, Machines, Suppliers & Information