Electronics Forum: parts getting damaged (Page 9 of 349)

Approximating parts count on started reels

Electronics Forum | Tue May 14 18:07:27 EDT 2002 | soupatech

My method is not good if accuracy is an issue. Most of our reels come with a guage on the back. It is not a perfect count but with a good eye you can get within a couple hundred on reels of 5k. On the reels shipped with no guage I usually just hold a

Handling/storing SMT leftover parts - cut strips

Electronics Forum | Tue Dec 12 15:08:37 EST 2023 | tommy_magyar

We are building our own products and we tend to keep our strips in bags. The same goes for bulk bags. What I would do, should there be no management issues, is to throw any bulk/strips of resistors and capacitors away, as any additional handling giv

Re: Heat sinking delicate leaded parts

Electronics Forum | Wed Feb 16 05:00:50 EST 2000 | Dean

What is the package type? TO92, TO5...etc. This temp. sensing device clips (mechanically) to the sink. And this requires a special tool? How about thermo bond heat sink compound? "output" by loc tite is the only flavor I can think of...There a

Re: Heat sinking delicate leaded parts

Electronics Forum | Wed Feb 16 05:00:50 EST 2000 | Dean

What is the package type? TO92, TO5...etc. This temp. sensing device clips (mechanically) to the sink. And this requires a special tool? How about thermo bond heat sink compound? "output" by loc tite is the only flavor I can think of...There a

Blow holes on radial parts solder joints

Electronics Forum | Fri Apr 06 11:37:19 EDT 2001 | raton

We had the same problem years ago when we started using a radial inserter. The inserter would dutyfully insert and clinch the leads. The problem in our case was the component body sealing to the fab, especially on electrolytics caps with a film jac

Lead free parts on a leaded assembly

Electronics Forum | Thu Oct 05 15:41:36 EDT 2006 | Mario Scalzo, SMT CPE

Good afternoon. From what it sounds like is that the solder joins are not getting hot enough or if it Au, then the increase in the Au content of the joint is increasing the melting point of the final solder joint. To some extent, this will also hap

Heller Oven blowing parts off reflowing

Electronics Forum | Thu May 18 08:31:28 EDT 2006 | marc

Hi James Short answer... yes... long answer...impingement velocity is excellent for heat transfer but it also is a higher risk of moving components. Variable speed blowers allow you to reduce the speed / impingment and more than likly your compone

Mirtec MV-2HTL programming: Teaching parts ...

Electronics Forum | Tue Jan 25 19:50:19 EST 2011 | bdamico

Hello Rodrigo, You are running a very old verson of software. The MIL library is also out of date. I think your organization should reconsider purchasing MIRTEC's second owner support package. MIRTEC charges a flat $6,000.00 fee plus travel expe

SIPLACE S15 FS02 - Spare parts after scrapp

Electronics Forum | Tue Jan 10 08:38:06 EST 2023 | niclas

I had some transport damage of a F3 and wonder if you are still carrying spare parts. 1. One leg was ripped out and tore the threads clean 2. The sliding covers on top are dented and could use replacement rather than trying to straighten them up.

Cleaning machine of rejected parts or misfed components?

Electronics Forum | Mon Jan 23 08:15:33 EST 2006 | pavel_murtishev

Good day, Vibratory (MultiStick) feeder is bottleneck of any placement machine. If you feed expensive IC�s via vibratory feeder they surely will be damaged. If you really care about expensive IC�s equip you placement machine with reject conveyor. In


parts getting damaged searches for Companies, Equipment, Machines, Suppliers & Information

Thermal Interface Material Dispensing

High Resolution Fast Speed Industrial Cameras.
Selective Soldering Nozzles

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Voidless Reflow Soldering

High Throughput Reflow Oven
PCB Handling with CE

World's Best Reflow Oven Customizable for Unique Applications


"回流焊炉"