Electronics Forum: pcb assy routing depaneling (Page 1 of 3)

Re: depaneling machines

Electronics Forum | Thu Dec 23 15:10:50 EST 1999 | Victor Salazar

What we did was design or panels with routed out edges held on by tabs. This was very effective. All we use is a pair of pneumatic scissors to cut off the tabs. We are using from single-to 13 layer PCB's and we have had no problems with delamination

Re: Issues depaneling

Electronics Forum | Tue Nov 24 11:13:11 EST 1998 | Keith

| A buddy of mine has problems after depaneling double sided pre-scored PCB's. Resistors near the edge, after put into the slice and dice machine contain micro cracks. He's checked for them before and after depaneling. We figure it is the sectioni

pcb separator

Electronics Forum | Fri May 11 17:21:04 EDT 2001 | davef

Three main groups of depaneling equipment are: 1 Scoring: Limited to straight edges and mainly 90� angles 2 Routing: And a cloud of dust 3 Singulating: Hard tooled by board To get started understanding the suppliers look here: http://www.cassembly.c

Repair of FR4 double-sided pcb

Electronics Forum | Thu Aug 22 22:10:26 EDT 2002 | davef

Ooooow! �Can it be fixed?� Good question. How BAD did you damage it? * Since you are asking this question, I am NOT inspired by the potential that you have the skills to fix the board. Go Jeff Ferry�s site at Circuit Repair Center [If you can�t f

PCB Depaneling Direction

Electronics Forum | Wed Oct 26 20:17:11 EDT 2022 | processman

Hello What direction routing path, clockwise or anti is preferred for bottom side routing (bit bellow PCB) with router bit rotating anti clockwise.

Re: Sony Routing Machine

Electronics Forum | Mon Jan 04 23:22:33 EST 1999 | Steve Evers

| Does any one have some information on Sony routing machines? Do you know the website, the contact? Thanks. | As in PCB depaneling? The last two Sony integrated lines I saw were using the new patented Die Cutting depaneling technique, not routers.

Re: Sony Routing Machine

Electronics Forum | Wed Jan 06 03:40:47 EST 1999 | Ken Mok

| | Does any one have some information on Sony routing machines? Do you know the website, the contact? Thanks. | | | As in PCB depaneling? | The last two Sony integrated lines I saw were using the new patented Die Cutting depaneling technique, not r

Router/Depaneling

Electronics Forum | Fri May 15 19:20:47 EDT 2009 | jlawson

if you have a budget for new machine, laser depanelising is pretty good for flex PCB as no physical stress on PCB like mechanical routing, thus fixturing is easier and less prone to moving the flex while cutting. Laser systens can also cut FR4 standa

Capacitor Shorts after Depaneling

Electronics Forum | Wed May 10 13:03:50 EDT 2006 | PWH

It sounds like your depaneling method is good. The only thing left to look at is to see if the depaneler is hitting the part somehow from the cutter or the bottom plates. I've seen time and time again where an operator has a part in contact with th

Tab-Routing

Electronics Forum | Mon Feb 20 14:45:51 EST 2006 | dannyleach

Histroically we have designed our pcb panel configurations around the v-score format. The QA Dept of our company is is suggesting that we revert back to tab-routing as away to avoid damage to senistive components like large package ceramic capacitors

  1 2 3 Next

pcb assy routing depaneling searches for Companies, Equipment, Machines, Suppliers & Information

Precision PCB Services, Inc
Precision PCB Services, Inc

Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.

Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

1750 Mitchell Ave.
Oroville, CA USA

Phone: (888) 406-2830