Electronics Forum | Fri Oct 19 10:49:48 EDT 2007 | brulal1
Hi I will like to know what do you think about cleaning hand solder, my employee spend about 25% of they time to brush they hand solder with teddy pen cleaner, we used no clean solder wire. It�s not been the first time that I try to eliminate those c
Electronics Forum | Thu Dec 03 07:09:59 EST 2009 | jdumont
We spray with an Asymtek C-740 system. However, some very small PCBs we do by hand and we also touch up after a PCB has to be repaired.
Electronics Forum | Wed Dec 02 14:54:52 EST 2009 | jdumont
Hi all, just wondering what type of brushes you all are using to manually touch up/apply your conformal coatings? We use an solvent based acrylic and do minor touch ups as they are processed. Occasionally we will have a bristle or two come off the
Electronics Forum | Tue Mar 25 08:29:33 EDT 2014 | sara_pcb
Please refer the attached jpegs, The problem is noticed after reflow soldering followed by conventional through hole soldering. Flux used one is MIL Std. Brush cleaning in IPA is followed after each soldering step. regards, R.Saravanan
Electronics Forum | Thu Sep 26 13:35:28 EDT 2002 | jersbo
Thanks to everyone who posted! I did get the boards clean and it worked well I used AIMTERGE 520A about 5% in HOT water.. I soaked for 10 minutes used a brush(handscrubber type)to loosen the residue. For the fine pitch I used a fine bristled small
Electronics Forum | Tue Sep 10 22:29:01 EDT 2002 | scottefiske
Many times after initially cleaning in the solvents recommended by the paste/material manufacturer, a light white haze may still be visable...try using a soft bristle brush to remove the remaining residues. By this time the residues that remain will
Electronics Forum | Tue Apr 09 16:19:37 EDT 2002 | Peter L.
Has anyone built using the ALIVH PCB (0402, 0.8mm pitch uBGA) on the SMT line? I would like to know any process issues (paste printing, p&p, reflow) related to processing this pcb. Specifically, what type of solder paste was used (no clean) and wha
Electronics Forum | Thu May 26 19:32:13 EDT 2005 | Mike Konrad
Three popular methods: Resistivity of Solvent Extract (ROSE) Test Method IPC-TM-650 2.3.25: The ROSE test method is used as a process control tool to detect the presence of bulk ionics. The IPC upper limit is set at 10.0 *g/NaCl/in2. This test is p
Electronics Forum | Fri Oct 19 13:04:14 EDT 2007 | brulal1
Thank Rob those are our own product, try few test by not clean some PCB never had any issue except on compoment under faraday cage. Did you know any norm that could persuade my boss and the R&D department that cleanning no clean is a waste of time. T
Electronics Forum | Fri Dec 15 11:06:06 EST 2006 | Gman
Hello All, Is Ionic Cleanliness testing using say an Ionograph on No-clean assemblies a valid test? If not, why? I understand factors like PCB cleanliness but is the 1.56ug/in2 IPC criteria valid for no-clean assemblies and can an Ionograph be used
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
winsouce.jpg)
