Electronics Forum | Tue Dec 10 13:35:34 EST 2019 | scotceltic
I am looking to see what people are using for a min-max range to supply your PCB fabricators regarding solder mask thickness. I saw some points in the archives but not too much regarding what people are providing as their spec ? Any help would be a
Electronics Forum | Wed Dec 11 12:07:33 EST 2019 | scotceltic
Our company has a spec on their current PCB dwg to make sure the fab house meets a specific thickness (min-max). The current spec reads: 13.5um min - 38.5um max. I assume it is to keep the board house honest and to make sure there is no exposed co
Electronics Forum | Tue Jun 07 08:31:57 EDT 2011 | bootstrap
I am building a rugged digital video camera product that essentially is just a sandwitch of 3 parts: #1: front piece is machined aluminum with C-mount thread #2: middle piece is 1/16" printed circuit board #3: back piece is machined aluminum The
Electronics Forum | Mon Oct 06 12:37:18 EDT 2003 | ramanandkini
It was a nice discussion. What I did here was a thermal shock test 1 hour@ +90 deg.c and immediately 1 hour @ -40 deg.c. The second test I did was a high humudity test for a week. After each test, I carried out a peel test with scotch tape. Those bo
Electronics Forum | Wed Oct 01 21:22:37 EDT 2003 | ramanandkini
We have a 1.6 mm thick automotive PCB board of size 35x70mm. One of our vendor has given us a batch with lesser soldermask thickness 5~8 microns. Will this affect the circuit board on a long term. What should be standard for the soldermask thickness?
Electronics Forum | Mon Aug 07 09:04:09 EDT 2006 | molos21
Hi everyone, I am starting to use the lead free process and I had a few wetting problems (solder did not reach top side) at the wave soldering process once the pcb had passed our smt line (one heat pass). From what I understand, I have had a problem
Electronics Forum | Tue Oct 07 08:38:05 EDT 2003 | davef
J-STD-001C requires removal of gold from (through-hole) component leads when the thickness of the gold layer is above 2.5 microns to prevent problems with embrittlement. The thickness of gold on an ENIG board typically is around 0.05 micron, resultin
Electronics Forum | Fri Feb 24 11:31:20 EST 2012 | pauld
I need to be sure of the Nickel/Hard Gold thickness to be specified on our drawing. We use hard gold on a slip ring pcb that has brushes riding over the conductive surface, so soldering is not the issue. I read through the hard gold vs immersion gold
Electronics Forum | Tue Feb 20 07:31:45 EST 2001 | Nick L
0.076 ~ 0.2 um(micron) but our substrate gold thickness is between 0.3~1.2um. Is there any related to the plating process of substrate! And how can they control this thickness?(May be I should ask substrate vendor their controlling limit). If this i
Electronics Forum | Wed Aug 09 08:06:07 EDT 2006 | davef
See "IPC-4554 Specification for Immersion Tin Plating for Printed Circuit Boards" 3.2.1 Immersion Tin Thickness. The most common reason for solderability issues with the white tin surface coating during multiple thermal excursions is a thin white ti
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
.gif)
.gif)
