Electronics Forum | Sat Nov 17 10:24:17 EST 2007 | etienne
Hi, I can give my opinion in this topic since I worked with both machines. To say the truth, I would recommend neither machine. First of all, operating software is much quite the same for both machines. The TP9 is true that has a larger footprint ov
Electronics Forum | Sat Jul 08 09:19:53 EDT 2006 | Larry
Samsung vs. Assembleon We currently have both Samsung/Dynatech and Assembleon Equipment. We started with two Samsung machines but the support, flexibility, component range, accuracy and speed of their machines just wasn�t there. The difference betw
Electronics Forum | Wed May 02 22:14:21 EDT 2007 | DSD
The Philips Orion (Yamaha YV100) Head I/O Board is usually at fault as this tends to suffer trackwork problems with age due to the constant flexing of the board stressing the connectors on the board, thus breaking tracks within layers. You should not
Electronics Forum | Wed May 02 09:14:08 EDT 2007 | stefi
Hi, We have a very annoying problem with a Philips Orion 2 SMT machine. It displays the error message "Second Limit Over" a few times per shift and it's impossible to make the machine work again unless it is turned off from the mains. It stops in th
Electronics Forum | Tue May 01 13:52:51 EDT 2007 | jasont
plz advise if the below feeders are compatible on CSM 46/60 (are they downwards compatible?); 1. Philips series FV-84-xxxxxC, model PA2903/70 (2,4 pitch, 8mm) QTY=29 2. Philips series FV-82-7-xxxxD, model PA2903/73 0603-type (2,4 pitch, 8mm
Electronics Forum | Wed Mar 17 11:31:45 EST 1999 | Quadmaster
| | I'm in the process of selecting a medium speed pick & place machine. I need to place a wide range of components from 0805 | | chips to a 144 pin MQFP (32mm square 25mil lead spacing). | | | | Anyway, I'm looking at the Quad QSA-30, the Philips
Electronics Forum | Fri Dec 15 11:01:14 EST 2017 | robertorocco
I have one Topaz X FNC machine with this problem. The head 2 FNC not change the nozzle. The head 4-6-8 is ok and change, but head 2 no, when he tries to change the nozzle he gives me an error message. What could be the problem?
Electronics Forum | Mon Mar 05 23:10:25 EST 2012 | vinitverma
The algorithm only checks if all the 8 parts can be picked up by 8 heads without any mechanical interference during pickup or during rotation. In case if foresees any interference it divides them into two different charges instead of one. You can try
Electronics Forum | Mon Mar 05 22:33:31 EST 2012 | acsscott
We are trying to optimize it to pick up 8 components, then move over the camera, then to the PCB and place them. In the Mount data, we load heads 2, 4, 6, & 8 with a 3216 Resistor, then them next 4 components are LED's, and are loaded on heads 1, 3,
Electronics Forum | Fri Mar 15 21:20:18 EDT 2024 | compit
Check out Yamaha - also old. A large number of parts (the same machines under the Assembleon, Philips brand), cheap feeders, many parts suppliers. Models from 2 to 16 heads, e.g. Emerald-X can accommodate 84 INDEPENDENT 8 mm feeders.
ORION provides innovative solutions to our customers' EMI/RFI Shielding, Insulating, Screening and Sealing needs in a broad spectrum of manufacturing environments.
Manufacturer / Distributor / Consultant / Service Provider
1 Orion Park Drive
Ayer, MA USA
Phone: 978-772-6000
