Electronics Forum | Thu Jul 15 15:41:00 EDT 1999 | Doug
| I'm designing a board where the parts will only fit if I do one of the following: | | 1. Put BGAs on both sides | | 2. Put BGAs on top, smt TSOPs directly underneath and using blind vias to keep the real estate on the bottom side below the BGA pa
Electronics Forum | Thu Jul 15 16:59:57 EDT 1999 | Glenn Robertson
| I'm designing a board where the parts will only fit if I do one of the following: | | 1. Put BGAs on both sides | | 2. Put BGAs on top, smt TSOPs directly underneath and using blind vias to keep the real estate on the bottom side below the BGA pa
Electronics Forum | Thu Jul 15 21:18:27 EDT 1999 | Scott McKee
| I'm designing a board where the parts will only fit if I do one of the following: | | 1. Put BGAs on both sides | | 2. Put BGAs on top, smt TSOPs directly underneath and using blind vias to keep the real estate on the bottom side below the BGA pa
Electronics Forum | Fri Sep 01 16:44:41 EDT 2017 | dgaddisatprimepower
I've been struggling trying to get our TP9 machine to place 8-dfn package parts. One of our primary assembly contracts uses a SOIC8 but the pad design accommodates an alternate 8-DFN part and sometimes we have to go to our alternate part due to lead
Electronics Forum | Thu Aug 20 15:12:44 EDT 2015 | superlen
I don't know that you find anything off the shelf that fits all of your requirements, but it wouldn't be too hard to create a system that does *most* of what you want. You could at least have it read the code off the pcb & alarm if it doesn't match
Electronics Forum | Wed Aug 24 16:30:11 EDT 2016 | shawn_halo_1
I have a 1oz Flex PCB (FPC) that has 2 0.4mm pitch connectors that need to be SMTd and 9 4.5x1.0mm pads that have conductive rubber contacts that are press fitted onto the FPC. The FPC has a one time bend radius of 15.5mm. Image is attached that show
Electronics Forum | Thu Sep 23 23:58:01 EDT 1999 | Earl Moon
| | Jackie's posting recently and responses to it got me to dondering. First, recollecting, we bought an IR rework station a couple million years ago. It had a IR source on a stand, a bunch of lenses, and Reynolds aluminum foil for shielding near-b
Electronics Forum | Thu Jan 31 14:10:11 EST 2019 | lapskrfc
I’m setting up an RF and mm-wave lab in a university. My idea is to purchase a set of machines using which I can do pcb prototyping, solder pasting, picking and placing the components (the smallest footprint would be 0201), and soldering (oven). In a
Electronics Forum | Mon May 02 12:35:33 EDT 2016 | adamjs
Or try : http://www.sipad.com/ I think sipad is incredibly cool and would be the perfect solution, but is way too expensive. We're paying $0.80/each for four-layer ENIG boards, 50cm^2 with 0.125mm trace/space and 0.8mm-pitch LGA landings in lots of
Electronics Forum | Tue Jul 19 09:06:00 EDT 2016 | davef
We used to use those, back in the bad old times. basically, it's a router with a blade on it that is used to trim the leads of PTH components that are mounted on boards. Nasty process. Difficult to control. Messy, firing cut leads all over the plac
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
