Electronics Forum: s20 placement count (Page 1 of 13)

Large component count board

Electronics Forum | Fri Aug 03 17:21:03 EDT 2012 | kmots15

We will be running a very large board with 62k+ components on it in the coming week. Has anyone run boards with this qty before? For sanity sake I had to split up the board into 12 individual programs. We will be forced to run it on a My12 due to

Large component count board

Electronics Forum | Mon Aug 06 14:08:56 EDT 2012 | dyoungquist

We run a MY12 and our largest layout has 9700 components of which about 8500 (88%) are placed by the Hydra head. Average run time for our layout is 75 minutes. Based on that and depending on what percentage of your components are Hydra mountable, y

real placement rates

Electronics Forum | Wed Jul 22 17:37:54 EDT 1998 | Jim Lewis

Does anyone have an idea of what a good placement rate (pph) is for a low volume, high mix smt line? We do small lots (10-300pcs), with a feeder count that ranges from 28 to 130 per setup. We have low volume machines (an old (real old) Siemens HS-180

Re: real placement rates

Electronics Forum | Wed Aug 05 10:50:06 EDT 1998 | Jim Price

| Does anyone have an idea of what a good placement rate (pph) is for a low volume, high mix smt line? We do small lots (10-300pcs), with a feeder count that ranges from 28 to 130 per setup. We have low volume machines (an old (real old) Siemens HS-1

0201 placement on Fuji CP4-3

Electronics Forum | Thu Mar 01 16:39:29 EST 2012 | triadelectronics

Our company is going to attempt to place 0201 components using our Fuji CP4-3 with the upgraded SMD3 vision system. Count On Tools is providing the 0.4 mm nozzles and we are using our 8mmX2mm feeders with the 0.7mm tape leaf (if it works at all we w

BGA placement using MCS-16 & IP-3

Electronics Forum | Fri Jun 24 01:01:41 EDT 2005 | FAC

If you are only concerned with the outline and it has 4 corners, VT-10 or 254 will work with backlighting. If the FIP3 machine has a 4400 card installed, frontlighting with high I/O counts could take a while during vision processing. If your machine

What is a typical SMT placement defect rate?

Electronics Forum | Wed Jul 09 14:47:39 EDT 2014 | deanm

I'm looking for a typical SMT placement defect rate from others in the field so I can judge whether or not we are in an acceptable range. If I give you a board with 200 components (0603, 0805, SOICs, 20mil MSOPs, tantalums, DPAKs and a few 20mil fin

RV/D axis counting error. (S20)

Electronics Forum | Thu Jul 27 09:48:16 EDT 2006 | john_smith

Seth, have you tried the zero point on the star?

RV/D axis counting error. (S20)

Electronics Forum | Sun Jul 30 11:50:22 EDT 2006 | john_smith

Do the sleeves spin freely in the segment? Could also be that the reader needs to be readjusted.

RV/D axis counting error. (S20)

Electronics Forum | Tue Aug 01 17:12:48 EDT 2006 | seth

My problem solved. I had to re-adjusted the reader,

  1 2 3 4 5 6 7 8 9 10 Next

s20 placement count searches for Companies, Equipment, Machines, Suppliers & Information

Count On Tools, Inc.
Count On Tools, Inc.

COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.

Manufacturer

2481 Hilton Drive
Gainesville, GA USA

Phone: (770) 538-0411

2024 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven
Electronics Equipment Consignment

World's Best Reflow Oven Customizable for Unique Applications
SMT feeders

High Precision Fluid Dispensers
SMT feeders

Training online, at your facility, or at one of our worldwide training centers"
design with ease with Win Source obselete parts and supplies

"回流焊炉"