Electronics Forum | Fri Oct 03 07:49:19 EDT 2008 | grantp
Hi, I just saw the new NXT machines at globaltronics in Singapore, and mostly they are faster. However what was interesting is Fuji shows a prototype of the new XPF machine, but it was called XPF-W which handles really large PCB's and uses the sam
Electronics Forum | Thu Oct 02 01:47:57 EDT 2008 | myleb
I'm new to SMT. Now, i'm making program for SPI machine to inscpect for solder paste of SP60-MU. I think this is a very good printer but some times, my program shows only 50-60% of volume transfer; and the average height is very high: nearly 200 pct.
Electronics Forum | Fri Mar 04 11:00:37 EST 2005 | mrduckmann2000
Anybody have any ideas on the proper way to screen solder mask onto a PCB? I am going to cover SMT parts that were soldered to the btm side of the PCB, now I have to mask them in order to run this animal through the wave solder process. I know it w
Electronics Forum | Sun Mar 06 20:08:38 EST 2005 | mrduckmann2000
Davef, You have a good question. If we had perfect design engineers out there that would use the proper component spacing and not put SMT parts between and around thru-hole parts - glue and wave would work perfectly. I have done this with great su
Electronics Forum | Wed Oct 14 13:52:59 EDT 1998 | Bill Schreiber
Dear Sanjay, An important issue involved when stencil printing adhesives vs. solder paste is: How do you clean the stencils after printing? Do you need two machines? Two chemistries? Two waste streams? What are the potential environmental impacts an
Electronics Forum | Thu Jun 21 22:04:18 EDT 2001 | davef
This is my attempt at beating the "Fuzzburg 7" translator used on the SMTnet Forum that mashes everything it sees. Below the next paragraph are three paragraphs,each with a common numering sequence, where each paragraph represents the columns of a t
Electronics Forum | Thu Dec 16 15:00:20 EST 2004 | glaucon
Simple differences. Both processes require a very similar machine platform, controlled motion, vision fiducial recognition and alignment of a substrate (PCB or hybrid ceramic) to the "image", the image being either a stencil (hence stencil printing)
Electronics Forum | Thu Sep 10 17:10:00 EDT 1998 | Steve Gregory
Hi Tim, 8-mil huh? Boy, that's getting down there...you know, placing 8-mil is one thing, but printing solder paste on 8-mil pitch is another. Most of the time when I've seen 8-mil pitch on a board it's been attached with hot-bar...but I guess
Electronics Forum | Fri Mar 06 10:30:46 EST 1998 | Ron Costa
| | | Hello everyone! | | | Does any know anything about bare board size variations? | | | Is there a spec. or tolerance? | | | I'm running small lots of boards and during the screen printing process | | | I find that I cannot paste each board perfec
Electronics Forum | Mon Sep 23 07:40:17 EDT 2019 | spoiltforchoice
A fair price.... well its the feeders that retain value. I know if you were to sell an Essemtec distributor a machine with say 10 banks of CLM feeders that old, they would give you perhaps only £10k. Refurb CLM feeders are ~£3k gbp (or about 1/2 of n
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang， Fuhai Street，Fuyong
Shenzhen, 30 China
Phone: 13713862102
winsouce.jpg)