Electronics Forum: seperation (Page 1 of 24)

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 09:35:28 EDT 2014 | emeto

Have you tried to bake the boards before you process them?

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 10:31:05 EDT 2014 | sara_pcb

The boards are baked for 2 hours at 120 deg C Regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 08:29:33 EDT 2014 | sara_pcb

Please refer the attached jpegs, The problem is noticed after reflow soldering followed by conventional through hole soldering. Flux used one is MIL Std. Brush cleaning in IPA is followed after each soldering step. regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 11:25:18 EDT 2014 | horchak

The first impression I get is that the mask was applied over dirty or contaminated copper. What is the trace and land finish on the PCB? You also appear to have a wetting problem.

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 11:43:48 EDT 2014 | sara_pcb

It is Solder Mask on Bare copper, The land finish is HASL as per MIL-PRF-55110G which accepts trace of HASL as acceptable. Wetting is acceptable. regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 18 11:53:58 EDT 2014 | sara_pcb

Our contract manufacturing agency have procured pcbs from approved vendor. After assembly we found solder mask separated from the PCB on the epoxy area as patches. The top side is intact. also over the pcb tracks, the mask got damaged. In what c

seperation of soldermask and pcb

Electronics Forum | Wed Mar 19 08:38:13 EDT 2014 | davef

I can't picture much of what you're saying, not for nothing, I'm just not connecting. During assembly, solder mask can affected by heat and chemicals. Typically this would be during: * Soldering * Cleaning I will tell you this: Not to defend assem

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 13:55:05 EDT 2014 | horchak

Ok lets put it this way. If the PCB house used a high quality mask and properly applied it to a properly cleaned surface and properly cured it, then as Dave stated above there are only two things that can destroy it. Excessive heat and overly aggress

Solder Saver

Electronics Forum | Fri Jun 04 08:29:27 EDT 2004 | Cal

We use the Kester Solder saver here and seems to work well. on a side tangent Technical Devices has a Solder seperating machine used to seperate dross from the solder. I am pretty sure they use heat and pressure to seperate the two. www.technicalde

Fiducial replacements?

Electronics Forum | Tue Dec 18 22:20:54 EST 2007 | darby

Paul, For the Dek and following equipment - seperate all the "bad fid" pcbs and process them seperately. Drill a hole as accurately as you can through the bad fids making sure you leave some white area around them. Set up and run a seperate program u

  1 2 3 4 5 6 7 8 9 10 Next

seperation searches for Companies, Equipment, Machines, Suppliers & Information

Circuit Board, PCB Assembly & electronics manufacturing service provider

High Precision Fluid Dispensers
Void Free Reflow Soldering

Wave Soldering 101 Training Course
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Sell Your Used SMT & Test Equipment

World's Best Reflow Oven Customizable for Unique Applications
design with ease with Win Source obselete parts and supplies

500+ original new CF081CR CN081CR FEEDER in stock