Electronics Forum: seperation of pcb panel (Page 1 of 5)

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 09:35:28 EDT 2014 | emeto

Have you tried to bake the boards before you process them?

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 10:31:05 EDT 2014 | sara_pcb

The boards are baked for 2 hours at 120 deg C Regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 11:25:18 EDT 2014 | horchak

The first impression I get is that the mask was applied over dirty or contaminated copper. What is the trace and land finish on the PCB? You also appear to have a wetting problem.

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 08:29:33 EDT 2014 | sara_pcb

Please refer the attached jpegs, The problem is noticed after reflow soldering followed by conventional through hole soldering. Flux used one is MIL Std. Brush cleaning in IPA is followed after each soldering step. regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 11:43:48 EDT 2014 | sara_pcb

It is Solder Mask on Bare copper, The land finish is HASL as per MIL-PRF-55110G which accepts trace of HASL as acceptable. Wetting is acceptable. regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 18 11:53:58 EDT 2014 | sara_pcb

Our contract manufacturing agency have procured pcbs from approved vendor. After assembly we found solder mask separated from the PCB on the epoxy area as patches. The top side is intact. also over the pcb tracks, the mask got damaged. In what c

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 13:55:05 EDT 2014 | horchak

Ok lets put it this way. If the PCB house used a high quality mask and properly applied it to a properly cleaned surface and properly cured it, then as Dave stated above there are only two things that can destroy it. Excessive heat and overly aggress

seperation of soldermask and pcb

Electronics Forum | Wed Mar 19 08:38:13 EDT 2014 | davef

I can't picture much of what you're saying, not for nothing, I'm just not connecting. During assembly, solder mask can affected by heat and chemicals. Typically this would be during: * Soldering * Cleaning I will tell you this: Not to defend assem

Repair of FR4 double-sided pcb

Electronics Forum | Thu Aug 22 07:48:30 EDT 2002 | Dave Milk

While separating individual pcbs from a panel, operators have caused delamination of the edge of the board, at the tabs that were cut. How can these boards be repaired? The delamination causes them to fail J-STD-001C 9.2.1.1.d. Also, what would yo

Repair of FR4 double-sided pcb

Electronics Forum | Thu Aug 22 22:10:26 EDT 2002 | davef

Ooooow! �Can it be fixed?� Good question. How BAD did you damage it? * Since you are asking this question, I am NOT inspired by the potential that you have the skills to fix the board. Go Jeff Ferry�s site at Circuit Repair Center [If you can�t f

  1 2 3 4 5 Next

seperation of pcb panel searches for Companies, Equipment, Machines, Suppliers & Information

Precision PCB Services, Inc
Precision PCB Services, Inc

Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.

Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

1750 Mitchell Ave.
Oroville, CA USA

Phone: (888) 406-2830