Electronics Forum | Mon Sep 23 06:29:03 EDT 2019 | spoiltforchoice
Essemtec machines are quite good for small batch production. However you do need to bear in mind the FLX is quite small and depending how you use it and the options fitted might be limited on feeder count. You don't mention if this FLX is laser or
Electronics Forum | Thu Mar 05 23:04:44 EST 2020 | sarason
My advice for what it is worth. Your description of the problem at first glance suggests a communication problem, now is it the bus, the SMT machine or the PC. The bus could have a short or an open. The PC could have a dud controller card. or so co
Electronics Forum | Mon Jan 21 07:51:44 EST 2013 | ericrr
On used machines: The 'technical' owner of the company who recently sold up his part of the company said, "always give the machine a regular grease up!" otherwise the bearings might fail and that will cost BIG money to repair, he added that some ethn
Electronics Forum | Tue Sep 10 14:27:12 EDT 2013 | ericrr
There is 8 nipples on the X-Y frame that is used to grease the frame, I was told these need to be greased often, as if the bearings go dry and break down it would cost big money to replace the bearing. (not sure how this price compares to other machi
Electronics Forum | Tue Sep 19 14:52:40 EDT 2006 | bobpan
Grease every 2-6 months depending on the hours used. Dont overgrease.....and make sure you wipe off all excess grease after lubing because the grease always tends to get into the horseshoe sensors and then you will get motor error 4's untill you die!
Electronics Forum | Tue Jul 04 03:15:00 EDT 2006 | dougs
can't you pull the leadscrew cover back? you usually can on fuji machines. pull it back and clean the leadscrew down then smother it with grease and manually run the axis back and forth a couple of times. then repeat until the grease is not discol
Electronics Forum | Thu Jan 19 06:39:56 EST 2006 | dougs
It's been a few years since i worked on a CP machine but your st17 & 19 errors are probably down to grease in the clutches at the top of the shafts, if too much grease is put onto the turret gear during maintenance it tends to spray into these clutch
Electronics Forum | Wed Mar 16 17:43:33 EST 2005 | pmd
We grease acording to PM schedule. The cable is very old about 5 years. We run 2 shifts. The transducer program and burnin test show the varance that we are seeing phisically so I can rule out the transducer. The motor may be the cause as it is of 19
Electronics Forum | Wed Sep 04 10:10:10 EDT 2019 | jameshoward
I know exactly what your problem is as I have seen it many times. Your problem is with indexer 1 (the cylinder which runs up and down and actuates feeders on side 1). At each end of the travel of the indexer is a micro switch hidden down below the be
Electronics Forum | Wed Jun 24 08:19:59 EDT 2009 | fujiphil
Hi, Procedure how to replace the x-ballscrew of CP642. 1. Before you remove the x-motor, remember the pulse of x-axis motor just it turn ON the zero set sensor. Pulse usually at 1000pls. +/-50pls. 2. Turn Off the machine. 3. Compress the two ballsc
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang， Fuhai Street，Fuyong
Shenzhen, 30 China
Phone: 13713862102
winsouce.jpg)