Electronics Forum | Thu Jan 19 06:39:56 EST 2006 | dougs
It's been a few years since i worked on a CP machine but your st17 & 19 errors are probably down to grease in the clutches at the top of the shafts, if too much grease is put onto the turret gear during maintenance it tends to spray into these clutch
Electronics Forum | Wed Jan 01 13:03:06 EST 2020 | ramsus
hello experts i want to calculate my target of cph i have a panasonic line composed of three machines 1.CM602L 4 HEADS 12 SHAFT 2.CM602L 4 HEADS 12 SHAFT 3. CM602L 2 HEADS 8 SHAFT + 2 HEADS 3 SHAFT Best regards
Electronics Forum | Fri Nov 18 16:26:17 EST 2011 | olddog
Hi again Bob, I checked the theta motor coupling and the set screws are definately tight. I noticed that the theta motor drives an snti-backlash gear (nice design) so there is no play there. It appears that the gear drives a slotted shaft which is d
Electronics Forum | Mon Dec 18 21:23:13 EST 2006 | jgarver1
The spline shaft is bent. I have replaced a number of these over the years with the exact same symptoms. How is your placement? Your 180 degree placements should be skewed if the shaft is bent. 0 Degree placements are typically acceptable due to
Electronics Forum | Sun Mar 21 22:03:35 EST 1999 | Nick
It looks like your holders now require some maintenance. You will need to throughly clean all the holders of all dirt debris and then relube the holder lightly with T&D or grease. You will only need to lube the shaft of the nozzle change enagager an
Electronics Forum | Thu Mar 30 12:38:14 EST 2006 | Tech
Also why I am at it. In the book CP-6 Series Maintenance Manul ( Fuji Part # MNT-C060-11.3E ) in Chapter 4 page 4-1-11 it says " The clutches should therfore be cleaned regularly, using the grease cleaner (ThreeBond 2706) provided with the machine."
Electronics Forum | Wed Nov 16 12:22:43 EST 2005 | rlackey
CPH - 17000 to 40000 depending on compoent density & type. Typically 28K. 0603 rejection rate - negligible. Major breakdowns - none. However preventative maintenance is essential. There are 2 different types of shafts on machines, and some people
Electronics Forum | Mon Jan 21 07:51:44 EST 2013 | ericrr
On used machines: The 'technical' owner of the company who recently sold up his part of the company said, "always give the machine a regular grease up!" otherwise the bearings might fail and that will cost BIG money to repair, he added that some ethn
Electronics Forum | Wed Mar 05 10:02:47 EST 2014 | dyoungquist
Per the TPSys Version 2.4 Software Manual: Force sensor level not within limits. * Force sensor dirty (inside Z tool holder) * Bad force sensor connection Try this: Remove the tool from the Z Midas head. Take a cotton tipped applicator (Q tip) and
Electronics Forum | Thu May 14 16:25:35 EDT 1998 | Chrys
Last week I posted a message on rotary chip waves that stated that the drive shaft had a protective boot around a u-joint that degraded and exposed the joint. Someone from the manufacturer read it and contacted me. He told me the problem has been re
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang， Fuhai Street，Fuyong
Shenzhen, 30 China
Phone: 13713862102
