Electronics Forum | Fri Apr 20 09:52:25 EDT 2018 | ushir
Hey everyone, Ive recently discovered a problem where components picked are moving on a nozzle during the vision scan. Pick and Place being used is an iPulse M7-3L. When the scan camera scans across the components, the components are shifting on the
Electronics Forum | Thu Aug 04 22:02:25 EDT 2011 | fujiphil
IP3 camera calibration, you need the following: 1. Part camera resolution Jig. 2. 10mm nozzle for nozzle centering. 3. Button jig (skip). 4. Glass board and Glass parts. 1. Conduct the Camera resolution. Set the following Delta values: X=+/-0.1mm;
Electronics Forum | Mon Jul 02 09:30:19 EDT 2007 | cyber_wolf
Make sure that your C14 tool is black and that the tip is in good condition. Next, create a vision package for the 0402. I assume that your machine has a line scan camera.(Use it) 0402's do not mechanically center well unless your C14 and centering u
Electronics Forum | Thu Dec 29 10:14:27 EST 2011 | davef
Darpy's offset checking trick: One trick I always use is to make the first two placements in every program the same as the fiducial data picked up from a dummy feeder. These two placements are generally skipped. ** If I do have a problem then I unski
Electronics Forum | Thu Jan 05 12:33:30 EST 2017 | rgduval
If you haven't resolved this yet, I think you're going to want to go to either the part or the package (I'm not sure which one off hand), and make sure that the hydra heads/tools are selected for placement. You'll also want the vision set to the lin
Electronics Forum | Thu Dec 15 11:28:45 EST 2016 | huske
Depends on the size of the elec cap and the nozzle set you have. But if you can pick it up, the wrinkle on the top of the cap can be a PIA. All you need to do is make sure the cap is being taken over the line-scan/hydra camera to center only (no mec
Electronics Forum | Tue Mar 31 09:56:20 EDT 2020 | davef
On this page,... + Find the navbar, left margin, near the top of the page, comprised of blue-colored rectangles with white lettering + Scan down to the top third of the navbar + Click "Used SMT Equipment" + Select "Send RFQ" tab peach-colored, near c
Electronics Forum | Mon Oct 25 05:52:34 EDT 2010 | sachu_70
In csae you use 2 fiducial recognition, ensure that board fiducials are oriented across a diagonal and spaced far apart. Also, maintain a prefered dia between 1-2 mm for the fiducial on board to have have a better correction factor recorded during fi
Electronics Forum | Wed Feb 02 23:28:48 EST 2022 | cbeneat
Something we've run into in the past, not on those machines, a different brand completely, and I have no experience with yours. We were having what you described and what we found was during the part being scanned, there was a bolt that held the shro
Electronics Forum | Fri May 11 16:06:09 EDT 2018 | aj
answers: The software on these machines is kinda flakey and the manuals are almost useless. There are a lot of bugs in the vision software that bite you. I supported mirea/meridian equipment at a past job and my memory is a bit fuzzy, but here are
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
3 Road Xintang， Fuhai Street，Fuyong
Shenzhen, 30 China
Phone: 13713862102
winsouce.jpg)
