Electronics Forum | Thu Sep 23 17:31:12 EDT 1999 | DaveH
For another excellent vendor try EMC GlobalTechnologies in Pennsylvania (215)340-0650. Contact Marty Wetzel. | | | | | | any thoughs? | | | | | | thanks | | | | | | | | You should use pallets that stand the reflow as well so that no separation wi
Electronics Forum | Wed Jun 16 07:46:45 EDT 1999 | Glynn Technologies and Manufacturing
| We are a medium sized PCB assy. house manufacturing about 2000 motherboards a day. There is a major problem we are facing at the wave soldering stage, i.e. warpage of the PCB. As soon as the PCB touches the wave it warps severely from the centre
Electronics Forum | Fri Feb 16 06:47:38 EST 2007 | CL
vshan, We were using pallets (delmat with cavities for the flex) We put stips of double sided Kapton tape in the critical areas. The tape held up to the heat and kept the circuit flat for the QFP's and BGA's. We based our assembly process for this c
Electronics Forum | Mon Dec 04 14:27:18 EST 2006 | pjc
Solder preforms can be used in SMT assembly for through-hole pin-in-paste process. In this process and modified aperture is used to print the paste with standard stencil printing, then a solder preform is picked and placed by a machine into the solde
Electronics Forum | Wed Sep 22 10:03:07 EDT 1999 | Boca
| | | | i'm sure everyone has run into this at one point or another. I have a thin pcb .025 that is single up that has to be built on a pallet. does anyone have any tricks to the pallet design that will help to hold these boards down during the s
Electronics Forum | Tue Dec 04 14:31:50 EST 2007 | davef
Search the fine SMTnet Archives for previous discussion. This technique has been called 'pin-in-paste,' 'paste-in-hole,' 'intrusive reflow,' 'alternative assembly and reflow technology' and who can remember all the other consultant buzz-words. Look a
Electronics Forum | Tue Jan 02 16:49:14 EST 2007 | dyoungquist
I am looking for data on the yield of printed circuit board assemblies so that I can judge if our SMT line is performing up to typical industry standards. Following I will describe the details of the assembly and what our yield has been. Each board
Electronics Forum | Sun Jan 13 19:44:02 EST 2008 | grantp
Hi, We need to solder a USB plug onto a PCB in our SMT machines, and this is the same type of plug you see on USB storage devices. It's a very flat connector with 4 SMT pins, however the hard part is the bottom of the connectors is the same level
Electronics Forum | Tue Aug 18 17:49:16 EDT 2009 | dyoungquist
Is there a limit to how many times a pcb with components can be run through a reflow oven before the components start to degrade? Example: We load the SMT components on the bottom side of the pcb and run it through the reflow oven. Next we load the
Electronics Forum | Thu Sep 23 17:28:54 EDT 1999 | JohnW
| | | Question for you SMT guru's out there. | | | | | | What is the best way to support boards on Fuji's CP6 machine's x-y table...particularly for 2nd side SMT where the support side already has parts... I am toying around with the following meth
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694