Electronics Forum | Wed Sep 12 03:52:45 EDT 2018 | shascoet29
Hi, Is the IPC-A-610 applicable to CSP assemblies? Especially regarding the solder ball to solder ball distance versus the minimum electrical clearance for assembly(0.13mm/IPC-A-610). With a 0.4mm pitch component and 260 microns diameters balls, thi
Electronics Forum | Tue Jun 06 11:57:12 EDT 2006 | Chunks
IPC 610 says acceptable Class 1 (Class 2, 3 indicator) if they are entrapped/encpsulated balls within 0.13mm of lands or pads. or exceed 0.13mm in diameter. Defect Class 1,2,3: Solder ball violates min electrical clearance. Solder balls not entrap
Electronics Forum | Wed Jan 01 22:19:33 EST 2020 | sssamw
Solder ball attached on solder joint without violation minimum electrical clearance is acceptable. If your process parameter including stencil not changed, suggest you check if solder pasted being pushed out after IC placement, also check if solder j
Electronics Forum | Tue Dec 31 02:04:19 EST 2019 | sssamw
From the picture, I cannot see clearly solder ball violate electrical clearance or cause a short, maybe it is. What I can see is the solder paste has some misalignment although it doesn't printed in solder mask area, but actual position will reduce
Electronics Forum | Thu Aug 24 15:37:50 EDT 2006 | Chunks
Hi Any, This is from an earlies thread "Solder Ball After Reflow Process". Date: August 16, 2006 01:52 PM Author: Russ Subject: Solder Ball After Reflow Process Oven settings are meaningless here. What does the board see? It is the paste we a
Electronics Forum | Mon Jul 16 15:49:33 EDT 2001 | Steve
The solder balls you are talking about are caused by too much paste. Reduce the size of the stencil aperatures. Concerning removing the solder balls, the first thing you need to ask yourself is, do I need to remove them. IPC-610, 12.4.10 states, "Ac
Electronics Forum | Thu Nov 29 17:30:07 EST 2001 | davef
You give no clue of what you want to write about. Let's try this: J-STD-001, 8.3.1 Particulate Matter says words to the effect of solder balls / splats shall be neither: * Loose or able to be dislodged during normal service � NOR * Violate minimu
Electronics Forum | Thu May 26 08:52:42 EDT 2011 | davef
Phil Zarrow wrote a useful paper that could help in evaluating paste. Here read it ... Evaluating Solder Paste � Not An Option Contributed by Phil Zarrow of ITM an Independent SMT consulting firm With soldering being the dominant source of assembly
Electronics Forum | Thu Oct 26 11:49:54 EDT 2006 | sms_don
CW, The good news is that you are not trying to use SAC paste with SnPb balls for that would be a void generator due to the ball being liquidous while the SAC paste is still in a flux cleaning stage. Two points to consider: One, voids are not an i
Electronics Forum | Fri Aug 26 17:27:48 EDT 2005 | saragorcos
Hello there, Most probably, since the solder balls are entrapped, it is a process indicator, but refer to IPC 610-6.5.3.1 on Excess solder / solder balls / splashes - it really depends on what class you are manufacturing, and the minimum electrical c
Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab
Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China
Phone: 0755-33578694
.gif)
