Electronics Forum: speed calibration (Page 1 of 8)

Electrovert omniflow 10 speed control fail

Electronics Forum | Mon Apr 29 01:29:29 EDT 2013 | aemery

If your current problem with the conveyor speed was caused by the SMEMA issue, maybe you have a Board #1 problem. The SMEMA communicates to the computer through Board #1. The input signal from the speed encoder and the output analog voltage to the

Manual for ASM E BY DEC Screener

Electronics Forum | Wed Feb 23 20:48:14 EST 2022 | dekhead

MAINTENANCE, DIAGNOSTICS, RAIL SYSTEM, BELT SPEED CALIBRATION

Electrovert Omni 7

Electronics Forum | Mon Sep 28 14:27:08 EDT 2009 | soudomphong

I need help with conveyor speed in Omni Excel 7. It fluctuate, and never have a steady speed. I swapped the speed control card,calibrated, encoder, and I still have the same problem. Any help would be appreciated, thanks.

Solder balls

Electronics Forum | Thu Jun 24 23:00:36 EDT 2004 | yukim

Tried with several lots of solder paste, manufactured in Feb and March this year. Work ambient: 25C, 60~70%. Is this humidity too much? I'll reduce the ramp in our profile. One change: We changed the conveyor motor in our reflow oven just before the

Re: Calibration

Electronics Forum | Thu Jun 25 18:17:26 EDT 1998 | Earl Moon

| What is the industry standard for calibration compliance certification of SMT machines? and Flow Solder machines? | We are currently doing a Quality Audit on one of our manufacturing venders and this questions has been brought up. | Any help would

Omniflow 7 conveyor

Electronics Forum | Mon Jan 15 13:49:09 EST 2007 | leemeyer

Hello all, I am having some trouble with the conveyor speed on an Omniflow 7 reflow oven. Recent profiling showed that the conveyor was running to slow so I calibrated the speed using the instructions in the manual. After calibration there was no ch

Board in/out sensors on reflow machines, do they work well?

Electronics Forum | Mon Apr 15 20:03:59 EDT 2002 | Jones

They work great as long as your conveyor speed has been calibrated and checked on some type of PM schedule. On some oven types these sensors can warn you to possible problems with the conveyor speed. Say the oven is calculating that the board is movi

IP3 placement for BGA / MicroBGA

Electronics Forum | Tue Mar 17 11:06:33 EDT 2009 | cyber_wolf

We have never been able to get our IP3 to place BGA's consistently. We installed new bulbs,ran glass plate calibration,played with scan speeds, scan area etc. etc.... I would not recommend this machine for BGA's

Vitronics Unitherm 500

Electronics Forum | Fri May 13 18:17:33 EDT 2005 | pde

The encoder is a sealed encoder located on the down stream end of the oven. Call Vitronics / Soltec for tech support. There is a calibration procedure for adjusting the belt speed to compensate for loaded and un loaded conditions. Soltec can give you

Quad Machines? Good Points / Bad Points

Electronics Forum | Tue Apr 23 10:08:27 EDT 2002 | cnoonan

I want feedback from people that currently have these machines or that I have worked with them in recent years. No Quad reps please, although your opinion may be valuable it may be bias to Quad. Here are a few areas of good points and bad point I w

  1 2 3 4 5 6 7 8 Next

speed calibration searches for Companies, Equipment, Machines, Suppliers & Information

SMT feeders

High Precision Fluid Dispensers
Sell Used SMT & Test Equipment

High Throughput Reflow Oven
December 2024 Auction

Best Reflow Oven
Software for SMT

World's Best Reflow Oven Customizable for Unique Applications
SMT spare parts

Low-cost, self-paced, online training on electronics manufacturing fundamentals