Electronics Forum | Wed Dec 19 16:05:10 EST 2018 | ldavis
I created a spray fluxer for our wave solder years ago that is still working well although does consume a lot of flux and is also rather messy. It's cheap and easy though so what the heck, right? I just machined a manifold that will hold four BETE
Electronics Forum | Tue Dec 18 04:13:27 EST 2018 | bukas
hello everyone, i'm looking for a spray gun that can withstand flux aggression. I made air controlled prototype for ersa wave machine, but air guns wear out quickly and start to leak. I was thinking about Binks model 95AR or something with stainless
Electronics Forum | Tue Jun 08 13:06:53 EDT 1999 | Kevin Hussey
| | Hi,my master | | How to iron out such soldering bridge with below conditions: | | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | | 3.using spraying fl
Electronics Forum | Tue Jun 08 12:49:41 EDT 1999 | Dave F
| Hi,my master | How to iron out such soldering bridge with below conditions: | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | 3.using spraying fluxer and n
Electronics Forum | Tue Jun 08 08:40:37 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Tue Jun 08 08:38:15 EDT 1999 | Wister
Hi,my master How to iron out such soldering bridge with below conditions: 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB 3.using spraying fluxer and no-clean fl
Electronics Forum | Tue Jun 08 17:52:53 EDT 1999 | Chrys Shea
| | | Hi,my master | | | How to iron out such soldering bridge with below conditions: | | | 1.The component(Harness)lead pitch is 2.0mm,the lead length is 3.2mm. | | | 2.PCB width is 1.6mm.Pad size is 1.65mm.Its a single copper PCB | | | 3.using s
Electronics Forum | Fri Sep 04 02:09:03 EDT 2009 | sachu_70
Hi Walter, Do you refer to a sprayfluxer operation? The problem seems to be a parameter setting issue. 1. Ensure the wide angle spray reaches PCB with optimum jet pressure. You could pass a glass plate to understand flux coverage and view Jet pressur
Electronics Forum | Tue Feb 07 11:55:27 EST 2023 | tommy_magyar
What I would look at is the chemicals being used in the facility where the complaints are. Flux/flux gel, IPA, cleaning agents, etc. Perhaps you should limit the usage to certain people only, who would be trained how to properly use these. Something
Electronics Forum | Mon Mar 06 18:07:33 EST 2023 | ccouture
We recently installed a new solder wave machine, The spray fluxer has a pressurized tank and because we use an alcohol based flux, the spray fluxer system must be fed with nitrogen. Anyone has infos on what installation is prefered to supply this mac
Industrial Sensor Vision International specializes in advanced camera technology of high resolution fast speed cameras for automation, AOI, 2-D/3-D, SPI inspection and wafer inspection.
3 Morse Road 2A
Oxford, CT USA
Phone: +1 203 592 8723
.gif)
winsouce.jpg)