Electronics Forum | Thu Oct 11 17:44:30 EDT 2001 | aaelect
OK, OK. 672 ball BGA. The pcbs are PC Card bus size and are .015 thick. There are 3 on a panel with about 1/2" between and rails. The aluminum plates are about 3" by 7". There are 3 cutouts which allow for the parts from either side to protrude du
Electronics Forum | Tue Oct 09 20:27:13 EDT 2001 | davef
That�s a 672 BALL BGA, bud!!! It�s a BIG Mutha!!! [I know. I know. For some reason suppliers call balls "pins".] Let�s focus on: * Clarifying the units on your PCB and aluminum plate thickness measurements. * Describing your use of the aluminum pl
Electronics Forum | Thu Oct 11 22:25:50 EDT 2001 | davef
Bruce I�m with yall. Designers and fabricators say �pins�. You say: * BGA pins are 1mm [0.039�] pitch. * BGA pads are 0.4mm [0.0157�] diameter. * BGA pins are 0.6 mm [0.024�] side-to-side. * Board thickness is ~0.4 mm [0.015�] First, as you can
Electronics Forum | Mon Oct 08 23:17:48 EDT 2001 | Brad Arnold
We are trying to produce a PC Card bus assembly with a 672 pin BGA on one side. These pcb's are .015 thick. I believe the ball pitch is .5mm. The pcb's are plated with white tin. The pcb's are in a 1 X 3 array. We had 2 plates with appropriate cutout
Electronics Forum | Tue Jul 11 14:09:54 EDT 2006 | Chunks
Not reflowing completely. Slower = hotter. Try a slower conveyor speed.
Electronics Forum | Wed Jul 12 11:26:12 EDT 2006 | flipit
Hi, I believe you have classic gold imbrittlement here. With 80 microinches of gold you are way over the limit. You can try to reflow longer time and at a higher temperature. The gold does not melt into the solder joint. The gold dissolves into
Electronics Forum | Mon Dec 20 07:58:02 EST 1999 | pascal MATHIEU
hello guys ; we are using a fine pitch component(0.65mm) on a thick copper PCB (Cu = 90�m) ; in this case we notice that we are in the process'limits , because the different supplier of the PCB are not able to ensure a good stability of it's process
Electronics Forum | Tue Jul 11 12:59:26 EDT 2006 | mattkehoe@sipad.com
We are trying to apply solder to boards with 80 microinches of electro plated hard gold. No components involved, just print 63/37 paste and reflow. The results are very poor on some boards, not so bad on others? Pictures at http://www.sipad.net/thick
Electronics Forum | Wed Dec 08 04:19:16 EST 1999 | pascal MATHIEU
I am working in electronic automotive industry and today we are facing to a very serious problem : if we want to use a PCBoard with a copper thickness of 90�m + fine pitch circuit (0.65mm, 0.5mm) the supplier(several) of the PCB has some trouble t
Electronics Forum | Mon Jul 01 09:33:08 EDT 2019 | dbuschel
if you can't change the PCB materials or design at this point, you might be able to reduce it somewhat through the use of fixtures or edge stiffeners. Unless it is a particularly thick board, I don't think the reflow profile would be the issue. The t
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
.gif)
