Electronics Forum: through hole change over time (Page 1 of 32)

through hole questions

Electronics Forum | Tue Nov 18 09:54:49 EST 2014 | gregp

Hi Adam, Good question. I know I am seeking a lot of details. Here's the deal. Five years ago I acquired the assets of Contact Systems. Since then I have been re-manufacturing the CS-400E machine which if you are not familiar with is a light guid

through hole questions

Electronics Forum | Fri Nov 21 11:40:53 EST 2014 | gregp

Hi Spoilt, Thanks again for the feedback. It is really an eye opener for me. What I fail to realize is that perception, whether right or wrong, plays a big role in whether or not someone might consider a process change. Your first comment is reall

through hole today

Electronics Forum | Thu Sep 12 20:17:59 EDT 2013 | action_101

Good ole contact cs-400. I worked at two different companies that had these machines, all I believe were E's except 1 C. One place had one and the other place had 4 of them. Dont take this personally, but thank god my current employer doesn't have a

Change-over time savers.

Electronics Forum | Tue May 22 09:37:11 EDT 2007 | jdengler

Hi Joakim, I do not know the QP242 table, but on our GP-341, CP-IV-2 and IP-III we make a plate from plexiglass with milled holes to show where the supports go for each board. This is not as fast as the Gridlock but does not cost nearly as much. J

SMT Advantages over Thourgh Hole in Chart format

Electronics Forum | Thu May 24 16:51:04 EDT 2001 | Robert Culpepper

Does anyone have any sort of Chart comparisons for the advantages of SMT over Through Hole? I realize this is old material and for that reason I believe it's now hard to come by (in presentation format). I know someone trying to convince a mature ent

Re: smt reliability vs thru hole

Electronics Forum | Tue Jan 18 12:36:11 EST 2000 | Dave F

Dave: I haven't located something to support your contention, yet, and I'm not going to comment on the factors that drive reliability beyond component selection, because I know that you've got some sweaty-palmed sales type wringing his hands waiting

Re: Use of solder paste for leaded thru hole parts????

Electronics Forum | Tue Jun 30 18:37:19 EDT 1998 | Earl Moon

| Hi all . | Thanks to Ryan, Brian , Justin and Dave for the timely help earlier. | I would appreciate if somebody could help me in the stated issue: | I am trying to to place one thru hole 20 pin connector along with the SMT components by paste pri

Re: Use of solder paste for leaded thru hole parts????

Electronics Forum | Mon Jul 06 13:17:50 EDT 1998 | Upinder Singh

| | Hi all . | | Thanks to Ryan, Brian , Justin and Dave for the timely help earlier. | | I would appreciate if somebody could help me in the stated issue: | | I am trying to to place one thru hole 20 pin connector along with the SMT components by p

New to SMT Equipment

Electronics Forum | Wed Sep 17 13:00:25 EDT 2008 | mw_fl

For the most part there would not be a lot of change over. There are two primary boards at this time that would be run on the line that also use common components. At this point all but a couple of the pick and place machines we have looked at have t

Thru-Hole Equipment

Electronics Forum | Tue Oct 22 14:25:11 EDT 2002 | slthomas

Yeah, but can they place through-hole? We looked at Panasert's Radial a couple years ago. Some big advantages over the Radial Lead 5's that we had at the time, but couldn't deal efficiently with all of our electrolytic cap orientations. We wanted to

  1 2 3 4 5 6 7 8 9 10 Next

through hole change over time searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Throughput Reflow Oven
IPC Training & Certification - Blackfox

Training online, at your facility, or at one of our worldwide training centers"
SMT feeders

High Precision Fluid Dispensers
SMTAI 2024 - SMTA International

World's Best Reflow Oven Customizable for Unique Applications