Electronics Forum | Fri Oct 03 07:49:19 EDT 2008 | grantp
Hi, I just saw the new NXT machines at globaltronics in Singapore, and mostly they are faster. However what was interesting is Fuji shows a prototype of the new XPF machine, but it was called XPF-W which handles really large PCB's and uses the sam
Electronics Forum | Fri Sep 04 09:33:40 EDT 1998 | Stefan W.
| I need advice for locating 23 Gull wing LED's (all in a straight line) in the x,y, and z axis for a SMT PCB. It is a Hewlett Packard LED (P/N HMLA-QH00-01). The application uses a CCD to detect the position of a ball which floats in a resevior fo
Electronics Forum | Thu Sep 03 15:43:18 EDT 1998 | Tim Flanagan
I need advice for locating 23 Gull wing LED's (all in a straight line) in the x,y, and z axis for a SMT PCB. It is a Hewlett Packard LED (P/N HMLA-QH00-01). The application uses a CCD to detect the position of a ball which floats in a resevior for
Electronics Forum | Wed Jun 09 17:53:06 EDT 1999 | Tom B.
| I am interested in seeing how some of you quote smt work. Currently we quote off a bom without component packages known then look in data books to find out what type of component they are. This job will be mine soon but i really believe there is a
Electronics Forum | Wed Dec 15 04:59:40 EST 1999 | Joshua Hall
Hello KA, When producing in kind of PCB product you have to base much of your decision on cost effectiveness, time, and quality. In order to get the best of all three you have to decide which you want to be your top priority. By adding an epoxy to
Electronics Forum | Sun Oct 04 20:55:44 EDT 2009 | phomann
Hi, I have a test pcb that came with my Yamaha YM84S machine. The board contains land patterns, fiducials, etc. The pyrpose of the board is to test the placement and vision systems in the machine. Does anyone provide the technical drawing of the bo
Electronics Forum | Sun Dec 26 16:13:49 EST 2010 | sam
Hi, Here is a brief synopsis of PNC - PNC has been a quality manufacturer of rigid printed circuit boards for 40 years. Located in Nutley, NJ, we are the largest shop in the North East. PNC provides complete turnkey jobs from design, PCB fabricatio
Electronics Forum | Tue May 17 03:48:51 EDT 2005 | Base
YV100, easy... YV112 uses a dual work-area, dual gantry machine in which the gantry does X and the PCB-table does Y movements. Also each gantry can only work on one PCB work-area and can pick form only one side of the machine. Basically you have two
Electronics Forum | Sat Nov 05 20:23:11 EDT 2016 | sarason
Close but not to close, would have to be the spec. Or depends on your separating technology. Prerouted boards on a panel, you could go right up to the edge. V-grove you will need more distance, maybe 2mm's or more. The distance from the panel edge to
Electronics Forum | Wed Oct 28 02:03:18 EST 1998 | Erhard Hofmann
| | | We currently using the Panasert SMT machine where PCB flow | | | direction were from right to left, & we are planning to move | | | in the FUJI -CP3 & CP4-2 in line where standard PCB | | | flow direction were left to right. | | | Any comment o
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
