Electronics Forum | Thu Feb 16 20:55:57 EST 2017 | youngbuck
Was wondering if anybody has experience a zone that will not get up to temperature. I changed the Solid state relay, made sure the thermocouple is working. The only thing I can think of is the bottom heater panel has a corroded/broken wire which is a
Electronics Forum | Wed Sep 15 07:34:49 EDT 1999 | Edmund
Hi, Can someone pls suggest to me the best reflow temperature setting for a force air convection oven. The details is as follow. 1) Heller 1700s 2) 12 zone---6 top and 6 bot 3) Solder paste --- Qualitek 691 non clean 4) board size : 159mm X 159mm
Electronics Forum | Wed Sep 15 10:55:21 EDT 1999 | Scott S. Snider
| Hi, | | Can someone pls suggest to me the best reflow temperature setting | for a force air convection oven. The details is as follow. | 1) Heller 1700s | 2) 12 zone---6 top and 6 bot | 3) Solder paste --- Qualitek 691 non clean | 4) board size :
Electronics Forum | Wed Sep 15 07:43:12 EDT 1999 | Earl Moon
| Hi, | | Can someone pls suggest to me the best reflow temperature setting | for a force air convection oven. The details is as follow. | 1) Heller 1700s | 2) 12 zone---6 top and 6 bot | 3) Solder paste --- Qualitek 691 non clean | 4) board size :
Electronics Forum | Wed Sep 15 12:07:50 EDT 1999 | Earl Moon
| | Hi, | | | | Can someone pls suggest to me the best reflow temperature setting | | for a force air convection oven. The details is as follow. | | 1) Heller 1700s | | 2) 12 zone---6 top and 6 bot | | 3) Solder paste --- Qualitek 691 non clean | |
Electronics Forum | Thu Sep 16 12:06:29 EDT 1999 | Scott S. Snider
| | | Hi, | | | | | | Can someone pls suggest to me the best reflow temperature setting | | | for a force air convection oven. The details is as follow. | | | 1) Heller 1700s | | | 2) 12 zone---6 top and 6 bot | | | 3) Solder paste --- Qualitek 691
Electronics Forum | Thu Sep 04 02:43:09 EDT 2008 | benefon
Thanks This error only occurred with one oven profile with the reflow zone temperature set at 270�C. Perhaps it really has to do with the exhaust pull as the oven is operating very near its temperature limit with this profile. I will check that. Tha
Electronics Forum | Wed Sep 03 07:39:19 EDT 2008 | pjc
You may not be getting enough exhaust pull, so the cooling modules over temp. Try swapping blower motors to isolate that before buying one. STANDARD AIR OPERATION: - Load-end: 150 cfm (255 m3/hr) at the 4� (102 mm) stack (minimum requirement) - Unlo
Electronics Forum | Mon Mar 16 12:44:36 EDT 2015 | proy
soldering a very simple board in a very simple Accuheat oven. Can anyone give me basic starting point settings (conveyor speed and temperature) then we will profile using a mole from there. Paste 1) Tin Lead Paste 2) Chipquik low temp TL 165C PR
Electronics Forum | Wed Dec 17 03:26:17 EST 2003 | Kev
Hi Lads, Thanks for all of the replies. To answer a few of your questions..... My wave is a Hollis PT500N. It has 3 zones of pre-heater rod elements. Each individual element (601195-01) is 500 watts. There are 16 elements per zone so 8 Kw per zone.
