GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Embedded-IR-Heater-User-Guide-22140091.pdf
displayed parameter, including the name, of an existing recipe: 1. Touch the RECIPES button on the Main (pg 29) screen. The Recipe Manager (pg 31) opens. 2. From the Recipe Manager, select the recipe you want to edit per Select recipe (pg 15). 3. Using Keypad
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Advanced-FPC-Real-Time-Controller-User-Guide-22940009.pdf
Pressure Interface User Guide (PN 22800101). 2. Mount the Time Pressure Interface per How to Use Taper-Lock Mount instructions (PN 22200611). Interconnections NOTE: Use Connection locations (pg 7) to identify the ports on the rear panel of the controller. To
GPD Global | https://www.gpd-global.com/pdf/doc/Advanced-FPC-Real-Time-Controller-User-Guide-22940009.pdf
Pressure Interface User Guide (PN 22800101). 2. Mount the Time Pressure Interface per How to Use Taper-Lock Mount instructions (PN 22200611). Interconnections NOTE: Use Connection locations (pg 7) to identify the ports on the rear panel of the controller. To
GPD Global | https://www.gpd-global.com/co_website/pdf/coating/SimpleCoat-Operation-Guide-23100600.pdf
rails until it is snug against the board stops at 0,0 position. Figure 5-2. Calibration plate (PN 23116001) Chapter 5. Operations 18 SimpleCoat Operation Manual d. Using the X and Y jog buttons, center the tip of the needle over the hole in the
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/SimpleCoat-Series-Operation-Guide-23100600.pdf
through the work area for both heads. Click the applicable button: Calibrate Head 1 or Calibrate Head 2. c. Using the X and Y jog buttons, center the tip of the needle over the hole in the calibration plate. d. Using the Z axis jog buttons, adjust the tip
GPD Global | https://www.gpd-global.com/pdf/doc/SimpleCoat-Series-Operation-Guide-23100600.pdf
through the work area for both heads. Click the applicable button: Calibrate Head 1 or Calibrate Head 2. c. Using the X and Y jog buttons, center the tip of the needle over the hole in the calibration plate. d. Using the Z axis jog buttons, adjust the tip
GPD Global | https://www.gpd-global.com/pdf/doc/Embedded-IR-Heater-User-Guide-22140091.pdf
, of an existing recipe: 1. Touch the RECIPES button on the Main (pg 29) screen. The Recipe Manager (pg 31) opens. 2. From the Recipe Manager, select the recipe you want to edit per Select recipe (pg 15). 3. Using Keypad operations (pg 9), make desired
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Infrared-Preheat-Module-User-Guide-22140087.pdf
) confirm the status. Run system Run in heat mode To run the system in heat mode: 1. Verify the option of pass through mode is turned off. For details, refer to Run in pass through mode (pg 17). 2. Set the system to online per Set online/offline state (pg 17
GPD Global | https://www.gpd-global.com/pdf/doc/Infrared-Preheat-Module-User-Guide-22140087.pdf
) confirm the status. Run system Run in heat mode To run the system in heat mode: 1. Verify the option of pass through mode is turned off. For details, refer to Run in pass through mode (pg 19). 2. Set the system to online per Set online/offline state (pg 19
GPD Global | https://www.gpd-global.com/co_website/pdf/doc/FLOware-Import-Export-Data-Reference-Guide-22100024R-v2-9-3P.pdf
the fields need not be the same as data base order: fields can appear in any order. Even the required "Program" field can appear anywhere provided it is present. Line (2) describes program detail lines as containing the operation name and the (X,Y