GPD Global | https://www.gpd-global.com/co_website/pdf/doc/Temperature-Monitoring-Camera-Sensor-Guide-22200623.pdf
. The dispense system I/O system acts as the interface between the camera and the dispense system control software. When a camera alarm is triggered, the camera sends an input signal to the dispense system
GPD Global | https://www.gpd-global.com/pdf/doc/Temperature-Monitoring-Camera-Sensor-Guide-22200623.pdf
. The dispense system I/O system acts as the interface between the camera and the dispense system control software. When a camera alarm is triggered, the camera sends an input signal to the dispense system
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/06/688951_OvenSetupWizard-XP4021.pdf
“Cycle Duration” timer starts countdown. At the end of cycle duration time, cooldown mode gets loaded. If cycle duration timer does not start within cycle start check timer expires, oven loads cooldown with alarm message
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/06/593950_OvenSetupWizard_80xx_RevC-1.pdf
: Minimum Heater Rise: 5 Deg C or 9 Deg F (1 Deg C for IR-Panels) Rise Check: 60sec During startup sequencing, if heat zone temperature did not rise for minimum heater rise value within rise check period, the oven program will load cooldown with rise rate alarm
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/06/686047-Win98SE-Software-versions-HC1-controller.pdf
. Fixed program crash from journal file creation at midnight, switching alarm, channel setup screen. + 1.0.5.8 Used only for Sony ovens 1.0.5.9 ECN#5770 (Not Released) 1.0.5.91 ECN#5775 (Not Released) 1.0.5.92 (ECN#5779
| https://www.wesource.com/rework-systems-and-accessories/wenesco-6x6-hot-plate-with-chromalox-1600-controller-id-60293/
. Limit Acknowledge- Can acknowledge even though you are still in alarm condition (Output does not reset until condition cleared) or reset when not in alarm condition. Alarm output 2. With “Silence” option
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/06/593949_Ver8.0.0.9_Heller_oven-software-log-1.pdf
) by monitoring heater GFI trip 8.0.0.1 Feb-09-2015 - SMEMA 9851 entrance operation improvement, during board entry to not go off due to lot end or oven goes in warning or downstream becomes not ready etc
Heller Industries Inc. | https://hellerindustries.com/wp-content/uploads/2018/06/689011_Heller-XP_software_log_HC1_controller-4021.pdf
: Cool zone1 heater was not functioning in 4.0.0.6 - Audible alarm option added for backup belt feature for HP - ActiveX function for belt speed set-point is updated to provide accurate SP in decimal
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/nc32-a2-nozzle-cleaning-machine-153875?page=18&category=1154&order=list_price+asc
Pricelist Nozzle Cleaning Machine NC32-A2 /shop/nc32-a2-nozzle-cleaning-machine-153875 ¥ 0.00 0.0 CNY ¥ 0.00 ¥ 0.00 This combination does not exist
Qinyi Electronics Co.,Ltd | https://www.qy-smt.com/shop/nc32-a2-nozzle-cleaning-machine-153875?page=18&category=1154&order=list_price+desc
Pricelist Nozzle Cleaning Machine NC32-A2 /shop/nc32-a2-nozzle-cleaning-machine-153875 ¥ 0.00 0.0 CNY ¥ 0.00 ¥ 0.00 This combination does not exist
