ORION Industries | http://orionindustries.com/pdfs/shielding_lam.pdf
” Polyvinylchloride 0.010 - 0.040” 94HB to 94V-0 54” Polyamide Nomex® 0.005 - 0.030” 94V-0 36” PBTP Valox® 0.003 - 0.030” 94VTM-0 to 94V-0 48” Polyimide Kapton® 0.001 - 0.005” 94V - 0 36” ORION is a registered trademark of Orion Industries Incorporated
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/sonoscan/support/application-notes
Materials 1200 Titanium Bar Material Voids 1202 Molybdenum Plate Material Voiding 1203 Ceramic Material Voids and Virtual Cross-Section 1204 Polymer Coating to Aluminum Plate Delamination Other
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/sonoscan/support/application-notes/0053-flex-circuit-delaminations
Circuit Delaminations - Application Note 53 Sample & Method The attachment of an IC to a flex circuit was imaged from the back side of the flex
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/products/biomaterial-delivery-devices?con=t&page=15
. Ribbon Peel Nordson DAGE Nordson DAGE provide ribbon peel testing (up to 5kg) as an alternative to ribbon pull testing. Ribbon peel tests are mainly used for testing aluminum interconnects in microwave, high frequency,… First
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/compression-testing?con=t&page=3
. It is an ideal method for measuring glue, solder and sintered silver bonded areas. The… Creep Testing Nordson DAGE The Nordson DAGE 4000Plus micro materials test system applies loads to small samples and measures the tiny movements that take place over extended time periods
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/creep-testing?con=t&page=3
) as an alternative to ribbon pull testing. Ribbon peel tests are mainly used for testing aluminum interconnects in microwave, high frequency
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/die-shear?con=t&page=15
the tool above the substrate. Testing is similar to standard ball shear tests and is performed in accordance with: MIL STD 883 Low profile die shear testing is required when the die under test are very thin and their height profile is low relative to the surface that they are bonded to
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/die-shear?con=t&page=18
the tool above the substrate. Testing is similar to standard ball shear tests and is performed in accordance with: MIL STD 883 Low profile die shear testing is required when the die under test are very thin and their height profile is low relative to the surface that they are bonded to
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/flexural-testing?con=t&page=3
. It is an ideal method for measuring glue, solder and sintered silver bonded areas. The… Testing Stent Quality with Prospector Nordson DAGE Creep Testing Nordson DAGE The Nordson DAGE 4000Plus micro materials test system applies loads to small samples and measures the tiny movements that
ASYMTEK Products | Nordson Electronics Solutions | https://www.nordson.com/en/divisions/dage/test-types/fatigue?con=t&page=3
high force shear test to measure the adhesion between the die and the substrate. It is an ideal method for measuring glue, solder and sintered silver bonded areas. The
